Oracle netra X5-2 Installation Manual Download Page 116

Page: 116 / 152

Create the data partitions and filesystems as configured above [y/n]?: y

******************************************************

WARNING: All non-system data on the disk will be

permanently erased and unrecoverable.

Are you sure [y/n]?: y

The format process will take a few minutes. Once

the format process begins, it cannot be stopped.

Please do not power down or reboot the system until

the format process is complete.

Continue [y/n]?: y

*** Beginning format process ***

*** Removing previous data partitions - please wait ***

*** Creating new data partitions - please wait ***

*** Formatting partition /VOLUME1. Please wait... ***

mke2fs 1.41.14 (22-Dec-2010)

[...]

Writing inode tables: done

Creating journal (32768 blocks): done

Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 37 mounts or

180 days, whichever comes first. Use tune2fs -c or -i to override.

*** Formatting completed successfully ***

*** Formatting partition /VOLUME2. Please wait... ***

mke2fs 1.41.14 (22-Dec-2010)

[...]

Writing inode tables: done

Creating journal (32768 blocks): done

Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 23 mounts or

180 days, whichever comes first. Use tune2fs -c or -i to override.

*** Formatting completed successfully ***

*** Formatting partition /VOLUME3. Please wait... ***

mke2fs 1.41.14 (22-Dec-2010)

[...]

Writing inode tables: done

Creating journal (32768 blocks): done

Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 31 mounts or

180 days, whichever comes first. Use tune2fs -c or -i to override.

*** Formatting completed successfully ***

*** Format finished successfully

New partitions have been created ***

*** Mounting partitions ***

e2fsck 1.41.14 (22-Dec-2010)

VOLUME1: clean, 11/5914624 files, 418265/23626953 blocks

/VOLUME1 mounted

e2fsck 1.41.14 (22-Dec-2010)

VOLUME2: clean, 11/11821056 files, 789884/47254150 blocks

/VOLUME2 mounted

e2fsck 1.41.14 (22-Dec-2010)

VOLUME3: clean, 11/11821056 files, 789884/47253628 blocks

/VOLUME3 mounted

Chapter 9

Formatting Procedure

9-4

Summary of Contents for netra X5-2

























































































































































Search results

Summary of Contents for netra X5-2

Reviews:

Related manuals for netra X5-2

Brands by name

Popular brands

Oracle netra X5-2, Installation Manual

Search results

Summary of Contents for netra X5-2

Reviews:

Related manuals for netra X5-2

Brands by name

Popular brands