background image

Appendix

Version 1.0.1 - 2020-08-10

19

Translation of original instruction

GU30S

EN

GU30S

_GB

.f

m

6.2

Liability claims/warranty

Besides the legal liability claims for defects of the customer towards the seller, the manufac-
turer of the product, OPTIMUM GmbH, Robert-Pfleger-Straße 26, D-96103 Hallstadt, does not
grant any further warranties unless they are listed below or were promised as part of a single
contractual provision.

Liability or warranty claims are processed at OPTIMUM GmbH's discretion either directly or 
through one of its dealers. 
Any defective products or components of such products will either be repaired or replaced 
by components which are free from defects. Title to replaced products or components is 
transferred to OPTIMUM Maschinen Germany GmbH.

The automatically generated original proof of purchase which shows the date of purchase, 
the type of machine and the serial number, if applicable, is the precondition in order to 
assert liability or warranty claims. If the original proof of purchase is not presented, we are 
not able to perform any services. 

Defects resulting from the following circumstances are excluded from liability and warranty 
claims:
- Using the product beyond the technical options and proper use, in particular due to over-

straining of the machine.

- Any defects arising by one's own fault due to faulty operations or if the operating manual

is disregarded.

- Inattentive or incorrect handling and use of improper equipment
- Unauthorized modifications and repairs
- Insufficient installation and safeguarding of the machine
- Disregarding the installation requirements and conditions of use
- atmospheric discharges, overvoltage and lightning strokes as well as chemical influences

Neither are the following items covered by liability or warranty claims:
- Wearing parts and components which are subject to normal and intended wear, such as

V-belts, ball bearings, lighting, filters, seals, etc.

- Non reproducible software errors

Any services, which OPTIMUM GmbH or one of its agents performs in order to fulfil any 
additional warranty are neither an acceptance of the defects nor an acceptance of its obli-
gation to compensate. These services neither delay nor interrupt the warranty period.

The court of jurisdiction for legal disputes between businessmen is Bamberg.

If any of the aforementioned agreements is totally or partially inoperative and/or invalid, a 
provision which nearest approaches the intent of the guarantor and remains within the 
framework of the limits of liability and warranty which are specified by this contract is 
deemed agreed.

6.3

Advice for disposal / Options of reuse: 

Please dispose of your equipment in an environmentally friendly manner, by not placing waste
in the environment but in a professional manner.

Please do not simply throw away the packaging and later the disused machine, but dispose of
both in accordance with the guidelines laid down by your city council/local authority or by an
authorised disposal company.

6.3.1

Decommissioning

CAUTION!

Immediately decommission used machines in order to avoid later misuse and
endangering of the environment or of persons.

Unplug the power cord.

Cut the connection cable.

Remove all operating materials from the used device which are harmful to the envi-
ronment.

Summary of Contents for 3101585





























Reviews: