OPTICOM SVD-2404A User Manual Download

Page: 10 / 137

Introduction

DVR User Manual

size

⚫

Support image and lens adjustment (only available for some cameras)

⚫

Support quick camera adding in the camera window of the live view interface

⚫

The live camera sequence of the web client will keep consistent with that of the DVR after

adjusting the live camera sequence of the DVR, but the live camera sequence of the DVR will
not be changed if that of the web client is changed

Disk Management

⚫

The DVRs with the 2U case can add a maximum of 8 SATA HDDs; a maximum of 4 SATA

HDDs with the 1.5U case, a maximum of 2 SATA HDDs with the 1U case and a maximum of 1
SATA HDD with the small 1U case

⚫

Each SATA interface of the DVR supports the HDDs with max 8TB storage capacity

⚫

Support disk group configuration and management and each camera can be added into different
disk groups with different storage capacity

⚫

Support disk information and disk working status viewing

⚫

Support batch formatting of the disks

Record Configuration

⚫

Support main stream and sub stream recording at the same time and collective or individual

configuration of the record stream

⚫

Support manual and auto record modes

⚫

Support schedule recording, sensor alarm recording and motion detection recording, etc

⚫

Support schedule recording and event recording setting with different record streams

⚫

Support record schedule setting and recycle recording

⚫

Support pre recording and delay recording configuration of the event recording

Record Playback

⚫

Support time scale operation in quick playback and the playback date and time can be set

randomly by scrolling the mouse; the time interval of the time scale can be zoomed

⚫

Support record searching by time slice/time/event/tag

⚫

Support smart search and playback

⚫

Support time view and camera view in searching by time slice mode

⚫

Support time slice searching by month, by day, by hour and by minute and time slice to be

displayed with camera thumbnail

⚫

Support event searching by manual/motion/sensor/intelligent events

⚫

Support tag searching by the manual added tags

⚫

Support instant playback of the selected camera in the live view interface

⚫

Support acceleration(maximum 32 times of the normal speed), deceleration (minimum

1/32 times of the normal speed) and 30s’ addition or reduction to current playing time

Record Backup

⚫

Support record to be backed up through USB (U disk, mobile HDD) interface

⚫

Support record to be backed up by time/event/image searching

⚫

Support record cutting for backing up when playing back

⚫

Support a maximum of 10 backup tasks in background and backup status viewing

Alarm Management

Summary of Contents for SVD-2404A










































































































































Search results

Summary of Contents for SVD-2404A

Reviews:

Related manuals for SVD-2404A

Brands by name

Popular brands

OPTICOM SVD-2404A, User Manual

Search results

Summary of Contents for SVD-2404A

Reviews:

Related manuals for SVD-2404A

Brands by name

Popular brands