manualshive.com logo in svg

Optical dimensions LASER CHECK 6212A, Manual, Page: 53 / 66

Share
Download
Optical dimensions LASER CHECK 6212A Manual Download Page 53

 

 

 

 

6212A Manual Version 14.56.docx

 

Page 45 of 58 

Measure/Align Dialog Box 

 

Horizontal Alignment with Measure/Align 

Measure/Align in the windows software will help you with horizontal alignment on cylindrical surfaces. 
Remember SUM is a sum of all of the voltages from the detectors. When horizontally aligned, you will obtain the 
largest possible value on Bar Graph and indicated percentage because more light is reflecting into the center of 
the detector window and detectors. Move the head back and forth 

COMPLETELY

 over a cylindrical surface. This 

allows software to “learn” the optimal position. You will see this value go up and down. Position Lasercheck for 
maximum signal after at least one complete pass over the cylindrical surface. The continually updating bar graph 
helps with horizontal alignment. 

Once it is found, then the head must be positioned to achieve a value as close to that maximum as possible. 

NOTE:

 

Do not assume that a 100% reading in the Measure/Align dialog box is correct. 

You must be sure to pass 

the head back and forth over the surface one or two times so that the maximum possible value can be learned

.

 

 

 

Summary of Contents for LASER CHECK 6212A



































































Reviews:

No comments