background image

24

25

Maintenance

Periodic inspection

Calibration

Long-term storage

When the Cover or the Display is soiled, first wipe away lightly with a clean soft 
cloth damped by diluted mild detergent solution and then wipe off moisture with a 
dry clean soft cloth. 

Inspect the following items every 3 months:
   

 Make sure that the Transmitter is fixed securely.

   

 Make sure that the Transmitter is not damaged.

   

 Make sure that the screws of the Terminal Block are not rusted.

The SC-T4 is designed so as to make measurements stably for a long time. In 
order to maintain the reliability of measurement, however, carry out calibration at 
least once a year (Refer to page 10 ([5] Operation (1) Calibration)).

When the SC-T4 is not used for a prolonged period, turn off the Power Switch 
and disconnect the Power Cable from the power supply prior to safekeeping.

10

Maintenance

CAUTION:

 Do not wipe the transmitter with solvent such as Thinner.

Calibration Output

Power Supply for Sensor (12 VDC)

Signal Output (analog 4-20mA, resistance load of 300

Ω

 or less)

Self-checking Relay Output (non-voltage C-contact  capacity 240 VAC, 1A resistance load)

Alarm Relay Output (non-voltage C-contact  capacity 240 VAC, 1A resistance load)

Detector signal input (analog 4-20mA, input resistance approx.100

Ω

)

Self-checking input

IEC 60529  /  IP65 (jetproof type)

AC100 

 240V

±

10%    50/60Hz

Power supply

Dimensions

SC-T4

0.1mg/l (0-49.9mg/l), 1mg/l (50-1000mg/l)

Output

Power 

consumption

Normal: 8VA or less, during washing: 16VA or less

 (including detector, at the time of analog signal input/output of 20mA)

Display resolution

Input (detector)

The specifications herein are subject to change without prior notice due to improvements.

11

Specifications

12

Dimensions

[mm]

16

38

75

34

34

34

34

220

Installation pitch 186

Installation pitch 125

240

(Max. 190)

162

Installation hole 

φ

9

Applicable cable 
diameter

φ

6~8

Hole for 
padlock

φ

7

Model No.

Main material

Operating temperature

-20 to +50 

 , humidity 95%Rh or less (Avoid direct sunlight)

Polycarbonate

Degree of protection

HxWxD = approx.162x240x75 mm

Weight

Approx. 1.6kg (including the Mounting Bracket)

Summary of Contents for SS Checker SC-T4















Reviews: