Opengear IP-KVM 1001 User Manual Download Page 97

Page: 97 / 109

KVM over IP User Manual

Page 97 of 109

Upload the new firmware file onto the IP-KVM unit

In order to do that you need to select the file on your local system using the

Browse

button. Click

Upload

. Once the firmware file has been uploaded, it is checked whether it is

a valid firmware file and whether there were any transmission errors. In case of any error

the Upload Firmware function will be aborted.

If everything went well, you see the

Update Firmware

panel

The panel shows you the version number of the currently running firmware and the

version number of the uploaded firmware. Pressing

Update

will store the new version and

substitute the old one completely

You will be advised when the firmware has updated successfully

The device will be rebooted and redirected to the login web page

Summary of Contents for IP-KVM 1001














































































































Search results

Summary of Contents for IP-KVM 1001

Reviews:

Opengear IP-KVM 1001, User Manual, Page: 97 / 109

Search results

Summary of Contents for IP-KVM 1001

Reviews: