background image

S

A F E T Y

  P

R E C A U T I O N S

5    

 OMRON STI  

© 

99885-0010 Rev.A 

—  Storing the status display touchscreen where the temperature is lower or 
higher than recommended in this manual can cause the LCD display liquid to 
congeal or become isotopic.
—  The LCD display liquid contains a powerful irritant. In case of skin contact, 
wash immediately with plenty of water. In case of eye contact, hold the eye open, 
flush with plenty of water and get medical attention.
—  The supplier is not responsible for modified, altered or reconstructed 
equipment.
—  Use only parts and accessories manufactured according to specifications of 
the supplier.
—  Peripheral equipment must be appropriate for the application and location.
—  The figures in this manual serve an illustrative purpose. Because of the many 
variables associated with any particular installation, the supplier cannot assume 
responsibility for actual use based on the figures.
—  The supplier neither guarantees that the status display touchscreen is suitable 
for 

customer’s particular application, nor assumes responsibility for 

customer’s 

product design, installation or operation.

3.2. P

OWER

 S

OURCE

The status display touchscreen is equipped with a 24VDC input. Supplying 
power other than 24VDC +/- 15% will severely damage the status display 
touchscreen. Thus, check the power supply supporting the DC power 
regularly.

3.3. G

ROUNDING

Without grounding, the status display touchscreen may be severely affected 
by excess noise. Make sure that the grounding is done properly from the 
power connector at the rear side of the status display touchscreen. When 
power is connected, make sure that the wire is grounded.

Use a cable of at least 2mm

2

 (AWG 14) to ground the status display 

touchscreen. Ground resistance must be less that 100 

 (class 3). Note that 

the ground cable must not be connected to the same ground point as the power 
circuit.

3.4. I

NSTALLATION

Communication cables must be separated from power cables for operational 
circuits. Only use shielded cables to avoid unpredictable problems.

Summary of Contents for Sti H-T40M-P






















Reviews: