Omron STC-SBA503POE Product Specifications And User'S Manual Download

Page: 7 / 59

No.13S094-05

7/59

STC-SCA503POE / STC-SBA503POE

Product Specifications and User’s Guide

1 Product Precautions



Do not give shock to the camera.



Do not haul or damage the camera cable.



Do not wrap the camera with any material while using the camera. This will cause the internal camera

temperature to increase.



When the camera moving or using the place that temperature difference is

extreme, countermeasure for dew

condensation (heat removal / cold removal) is necessary.



While the camera is not using, keep the lens cap on the camera to prevent dust or contamination from getting

in the sensor or filter and scratching or damaging it.
Do not keep the camera under the following conditions.

・

In wet, moist, high humidity or dusty place

・

Under direct sunlight

・

In extreme high or low temperature place

・

Near an object that releases a strong magnetic or electric filed

・

Place with strong vibrations



Apply the power that satisfies the specified in specifications for the camera.



The defective pixels may appear due to the sensor characteristics.



Use below recommend materials (or equivalent materials) to clean the surface of glass.

・

Air dust: Non Freon air duster (NAKABAYASHI Co., LTD.)

・

Alcohol: Propan-2-ol (SAN’EI KAKO Co., LTD.)

・

Non-woven: nikowipe clean room (NKB)



Use a soft cloth to clean the camera.

2 Warranty

■

Warranty period

One year after delivery (However, the camera had malfunction with camera uses correctly)

In below case for a fee even within warranty period.

・

The malfunction caused by incorrect usage, incorrect modify or repair.

・

The malfunction caused by external shock including the camera dropping after delivery the camera.

・

The malfunction caused by fire, earthquake, flood disaster, thunderbolt struck, other natural disaster or

wrong voltage.

■

Warranty coverage

Exchange or repair the malfunction camera if the malfunction is occurred by our responsibility.
“Warranty” mean is warranty for the delivered camera itself. Please accept the induction damage by the
camera malfunction is not included.

For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com

Aegis

Electronic

Group,

Inc.

Summary of Contents for STC-SBA503POE




























































Search results

Summary of Contents for STC-SBA503POE

Reviews:

Related manuals for STC-SBA503POE

Brands by name

Popular brands

Omron STC-SBA503POE, Product Specifications And User'S Manual

Search results

Summary of Contents for STC-SBA503POE

Reviews:

Related manuals for STC-SBA503POE

Brands by name

Popular brands