Omron STC-SBA503POE Product Specifications And User'S Manual Download

Page: 2 / 59

No.13S094-05

2/59

STC-SCA503POE / STC-SBA503POE

Product Specifications and User’s Guide

Table of Contents

Product Precautions....................................................... 7

Warranty .......................................................................... 7

Introduction ..................................................................... 8

3.1

Features .................................................................................................................................... 8

3.2

Product Number Naming Method ........................................................................................... 8

Specifications ................................................................. 9

4.1

Electronic Specifications ......................................................................................................... 9

4.2

Spectral Sensitivity Characteristics ..................................................................................... 11

STC-SBA503POE ............................................................................................................................. 11

STC-SCA503POE ............................................................................................................................. 11

IR Cut Filter (STC-SCA503POE) ..................................................................................................... 12

4.3

Mechanical Specifications ..................................................................................................... 13

4.4

Environmental Specifications ............................................................................................... 13

Connector Specifications ............................................ 14

5.1

RJ45 Connector ...................................................................................................................... 14

5.2

Power and Control Signal Connector ................................................................................... 15

Equivalent Circuit for the Input Pin of the I/O Connector ............................................................. 17

Typical Input Circuit ........................................................................................................................ 18

Typical Output Circuit ..................................................................................................................... 19

Input and Output Signal Timing (Hardware Trigger) ..................................................................... 20

Input and Output Signal Timing (Software Trigger) ...................................................................... 21

Dimensions ................................................................... 22

6.1

STC-SBA503POE .................................................................................................................... 22

6.2

STC-SCA503POE .................................................................................................................... 23

Sensor information ....................................................... 24

For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com

Aegis

Electronic

Group,

Inc.

Summary of Contents for STC-SBA503POE




























































Search results

Summary of Contents for STC-SBA503POE

Reviews:

Related manuals for STC-SBA503POE

Brands by name

Popular brands

Omron STC-SBA503POE, Product Specifications And User'S Manual

Search results

Summary of Contents for STC-SBA503POE

Reviews:

Related manuals for STC-SBA503POE

Brands by name

Popular brands