manualshive.com logo in svg

Omron STC-SBA503POE, Product Specifications And User'S Manual

Share
Download
Omron STC-SBA503POE Product Specifications And User'S Manual Download Page 46

No.13S094-05 

 
 
 

 

 

 

46/59 

STC-SCA503POE / STC-SBA503POE 

Product Specifications and User’s Guide 

 

9.11 

Save and load the camera setting data 

 

The camera has the camera setting including the factory default, load function. 
The camera has below two camera settings. 

 

Default: The factory default data (This data cannot change) 
UserSet1: Changeable data 

 
These camera settings load to the register in the RAM on the camera. 
The camera settings saving and loading is controllable with “UserSetSelector” and “UserSetDefaultSelector” 
parameters, and “UserSetLoad” and “UserSetSave” commands in UserSetControl category of GenICam. 
 
The details of the parameters and the functions are in the table below: 

 

GenICam parameters 

UserSetSelector 

Enumeration 
type 

Select “Default” or ”UserSet1” 
UserSetLoad or UserSetSave process for the selected data. 

UserSetDefaultSelector 

Enumeration 
type 

Select which settings (“Default or UserSet1”) load automatically 
when the camera power is on. 
Selection saves automatically. 

UserSetLoad 

Command type  The camera settings load from ROM to the register in RAM. 

UserSetSave 

Command type  The camera settings at the register in RAM save to ROM. 

 

 

The camera settings saving 

 
 
 
 
 
 
 
 
 
 
 
 

The camera settings saving procedure 
1.  Selects “UserSet1” at UserSetSelector. 
2.  Executes UserSetSave. 

 
 
 

 

When UserSetSave is executing,   
the camera settings in the register at 
RAM, save to ROM that is selected 
at UserSetSelector 

Caution: 
UserSetSave command is only 
available when “UserSet1” is selected 
at UserSetSelector 

ROM 

UserSet1 

ROM 

Default 

RAM 

register 

UserSetSelector 

Selector 

For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com

Aegis 

Electronic 

Group, 

Inc.

Summary of Contents for STC-SBA503POE




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands