background image

S8VS

30

Maintenance Forecast Monitor Function 

The Power Supply is equipped with electrolytic capacitors.
The electrolyte inside the electrolytic capacitor penetrates the sealing 
rubber and evaporates as time passes since it is manufactured, which 
causes deterioration of characteristics such as decreasing the 
capacitance, etc.
Due to this deterioration of the characteristics of the electrolytic 
capacitor, the Power Supply decreases its performance as time 
passes.

The maintenance forecast monitor function shows an approximate 
period left for maintenance of the Power Supply due to deterioration 
of electrolytic capacitors. When the period left for maintenance that 
the power supply forecasts reaches the set value, an alarm is 
indicated and an output signal is triggered.
Use this function to know the approximate replacement timing of the 
Power Supply.
Note: The maintenance forecast monitor function indicates an 

approximate period left for maintenance, based on 
deterioration of the electrolytic capacitor. It does not predict 
failures caused by other reasons.

Relationship between Indicated Values and Output of Set Values

Principle of Operation

The deterioration speed of the electrolytic capacitor varies 
considerably according to the ambient temperature. (Generally the 
speed follows “Rule of Two for every 10

°

C”; for every 10

°

C increase 

in temperature the rate of degradation doubles according to 
Arrhenius’s equation.) The S8VS-

@@@

24A

@@

 monitors the 

temperature inside the power supply, and calculates the amount of 
deterioration according to the running hours and inside temperature. 
Judging by this amount of deterioration, the power supply will give the 
alarm indication and output when the period left for maintenance 
reaches the set value.
Note: 1. Due to degradation of internal electronic parts, replace the 

power supply approximately 15 years after purchase even if 
indication and output of maintenance forecast monitor are 
not issued.

2. The maintenance forecast is accelerated or decelerated 

according to operating conditions. Periodically check 
indication.

3. Acceleration or deceleration of the maintenance forecast 

may cause the output to repeatedly go ON/OFF.
Only the S8VS-09024A

@@

, S8VS-12024A

@

, S8VS-

18024A

@

, S8VS-24024A

@

, and S8VS-48024A are 

equipped with output.

4. The accuracy of the maintenance forecast function may be 

adversely affected by applications in which the AC input is 
frequently turned ON/OFF.

Reference Values (15-W to 480-W Models)

Note: The maintenance forecast is the service life (the power 

supply’s internal temperature is monitored at all times) of the 
internal electrolytic capacitor in actual operating conditions, 
and varies according to the customer’s operating conditions. 
15 years is taken as the maximum period of the maintenance 
forecast.

(L

0.5)

5.0

L=2.5

L=0.5

2.5

2.0

1.5

1.0

0.5

0

Initial capacity

"1.0" is displayed on the main display for the 
duration that the maintenance forecast up to 
replacement satisfies the condition 1.0 

≤ 

1.5.

In case of setting L between 2.5 and 5.

Maintenance forecast monitor output

T: Maintenance time 

until replacement

The numerical value 
decreases with time.

Main display

Capacity of Capacitor

Capacity level
at replacement

Note: This function can be set only on the S8VS-09024A

@@, 

S8VS-12024A

@, 

S8VS-18024A

@, 

S8VS-24024A

@

, and S8VS-48024A.

L: Maintenance forecast set value (See note.) 

0.0 to 5.0, 0.5 steps

Item

Value

Definition

Reliability 
(MTBF)

15 W to 240 W: 
135,000 hr min.
480 W: 
60,000 hr min.

MTBF stands for Mean Time 
Between Failures, which is 
calculated according to the 
probability of accidental device 
failures, and indicates reliability of 
devices.
Therefore, it does not necessarily 
represent the life of the Product.

Life 
expectancy

10 yr min.

The life expectancy indicates 
average operating hours under the 
ambient temperature of 40

°

C and a 

load rate of 50%. Normally this is 
determined by the life expectancy of 
the built-in aluminum electrolytic 
capacitor.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Summary of Contents for S8VS-015 Series







































Reviews: