Omron R88D-KT Series Manual Download Page 35

Page: 35 / 42

9.3. Parameters Related to Position Control

SS2 series

G5 series

Remarks

Parameter

No.

[hex]

Parameter name

Default

setting

[dec]

Parameter

No.

[dec]

Parameter name

Default

setting

[dec]

Pn40

Command Pulse
Multiplying Setting

Set the input pulse multiplication function when
you set

0 or 2: 90° phase difference (phases A

and B) signal inputs

Command Pulse Mode

(Pn42).
● The default setting of the SS2 series is

Multiply the input pulses by 4.

● The G5 series does not have the related

parameter, but it always uses 4-fold input
pulses for judgment.
* To use 2-fold or so ones, use Electronic Gear

functions (Pn008 to Pn010) for adjustment.

Pn41

Command Pulse
Rotation Direction
Switch

Pn006

Command Pulse
Rotation Direction
Switching Selection

Set the motor rotation direction for command
pulse inputs.
● In both the SS2 and the G5 series, the default

setting is 0: The motor rotates in the direction
specified by the command pulse.

Pn42

Command Pulse
Mode

Pn007

Command Pulse
Mode Selection

Set the input form of input command pulses.
● In both the SS2 and the G5 series, the default

setting is 1: Reverse pulse/forward pulse.

Pn43

Not used.

Pn44

Encoder Dividing
Rate Setting

2,500

pulses/

rotation

Pn011

Encoder Dividing
Numerator

2,500

pulses/

rotation

Set the number of encoder pulses per motor
rotation to be output from the Servo Drive.
● In both the SS2 and the G5 series, the default

setting is

2,500 pulses/rotation

Pn45

Encoder Output
Direction Switch

Pn012

Encoder Output
Direction Switching
Selection

Set the logic of the encoder pulses to be output
from the Servo Drive.
● In both the SS2 and the G5 series, the default

setting is 0: Positive logic (Phase A advance in
forward operation).

Pn46

Electronic Gear
Ratio Numerator 1

10,000

Pn008

Electronic Gear
Integer Setting

10,000

Set the electronic gear function.
● The default setting of the SS2 series is

Pn46/Pn47 = 10,000, Pn4A = 0, Pn4B = 2,500

meaning 2,500 input pulses for one motor
rotation.

● The G5 series has two setting methods.

• Using

Electronic Gear Integer Setting

(Pn008)
Use

Electronic Gear Integer Setting

(Pn008) to set the number of input pulses for
one motor rotation. The default setting is

10,000

, meaning 10,000 input pulses for one

motor rotation.
* If you set

2,500

, it will become the same as

the default setting of the SS2.

• Using

Electronic Gear Ratio Numerator 1/2

(Pn009/Pn500) and

Electronic Gear Ratio

Denominator

(Pn010)

When you set

Electronic Gear Integer

Setting

(Pn008), the settings of Pn009,

Pn500, and Pn010 will be enabled.
* If

is set to

Electronic Gear Ratio

Numerator 1/2

(Pn009/Pn500), the

resolution of the motor in use will be set
automatically to the electronic gear
numerator.

* The G5 series does not have the

Electronic Gear Ratio Numerator
Exponent

parameter.

Pn47

Electronic Gear
Ratio Numerator 2

10,000

Pn009

Electronic Gear
Ratio Numerator 1

Pn500

Electronic Gear
Ratio Numerator 2

Pn48

Not used.

Pn49

Not used.

Pn4A

Electronic Gear
Ratio Numerator
Exponent

Pn4B

Electronic Gear
Ratio Denominator

2,500

Pn010

Electronic Gear
Ratio Denominator

10,000

Pn4C

Position Command
Filter Time Constant
Setting

Pn222

Position Command
Filter Time Constant

0.0
ms

Set the first-order lag filter time constant in the
command pulse input section.
● In both the SS2 and the G5 series, the default

setting is

0.0 ms

● Be careful in setting because the setting unit is

different.

Pn4D

Not used.

Summary of Contents for R88D-KT Series











































Search results

Summary of Contents for R88D-KT Series

Reviews:

Related manuals for R88D-KT Series

Brands by name

Popular brands

Omron R88D-KT Series, Manual

Search results

Summary of Contents for R88D-KT Series

Reviews:

Related manuals for R88D-KT Series

Brands by name

Popular brands