![background image](http://html1.mh-extra.com/html/omron/f3sn-b-p-series/f3sn-b-p-series_instruction-manual_744009061.webp)
Section 2 Wiring and Mounting
B-16
Setup procedure when the supplied mounting brackets are used
I.
Secure the bottom bracket (power connector
side) on a wall or column.
II.
Secure the intermediate bracket (3) on a wall or
column.
[Note]:
The intermediate bracket(3) of the
receiver is mounted upside down
compared with that of the emitter.
III.
Align the intermediate bracket (2) with the
protrusion of intermediate bracket (1) located on
the rear side of the light curtain, and temporarily
tighten the supplied screw (M4x6).
[Note]:
Mount the intermediate bracket (2) so
that its direction is the same as that of
the intermediate bracket (3).
IV.
Insert the cable connector of the light curtain
into the bottom bracket.
V.
Move the intermediate bracket (2) until its height
is aligned with that of the intermediate bracket
(3)(V-a), securely tighten the screw
(M4x6)(V-b).
[Note]:
Be sure to perform this step prior to
mounting the top bracket (cap side).
VI.
After having aligned the intermediate bracket (2)
with the intermediate bracket (3) in the direction
of mounting the light curtain, temporarily tighten
the supplied screw (M5x8).
Intermediate brackets (2) and (3) are assembled
in the following three ways; VI-a, VI-b, VI-c.
VII.
Align the top bracket (cap side) with the round
hole on the cap, and secure it on a wall or
column.
VIII.
Insert two supplied screws (M4x8) into both top
and bottom brackets, and temporary tighten
them (VIII-a, VIII-b). (The figure shown below
describes the side mounting.)
IX.
Adjust the torsion angle of the light curtain in the
point where the five light receiving level indicators
are lit.
X.
Securely tighten the bottom and top brackets.
XI.
Then, securely tighten the intermediate brackets. The procedure to mount the light curtain is now
complete.
[Rear mounting]
[Side mounting]
Emitting
surface
Top bracket
Intermediate bracket (2)
Intermediate bracket (3)
Bottom bracket
IX.
X.
XI.
III.
I.
II.
IV.
V-a.
V-b.
VIII-a.
VII.
VIII-b.
Rear mounting
Side mounting (1) Side mounting (2)
VI-a. VI-b.
VI-c.
Summary of Contents for F3SN-B P Series
