background image

4-5

H

Operation Specifications

Control input

Three photocoupler input terminals (24 VDC, 8 mA)

Forward/stop [SF]

Reverse/stop [SR]

Multi-function input [S1] (set in constant No. 06)

Multi-function input [S2] (set in constant No. 07)

Multi-function input [S3] (set in constant No. 08)

Note

When 3-wire sequence mode (constant No. 01 = “9”) is selected, the
terminals become as follows:

Run command [SF]

Stop command [SR]

Forward/reverse rotation command [S1]

Note

The standard Inverters are not provided with S2 and S3 terminals.

One analog input terminal (0 to 10 VDC or 4 to 20 mA)

Frequency reference input [Between FC and FR]

Control output

One SPDT relay contact output terminal [MA, MB]
(30 VDC and 1A; 250 VAC and 1A)

Multi-function contact output (set in constant No. 09)

One photocoupler input terminal [PA] (48 VDC, 50 mA)

Multi-function photocoupler output (set in constant No. 10)

Note

The standard Inverters are not provided with the multi-function photo-
coupler output.

Analog output

One analog voltage output [AM] (0 to 10 VDC, 2 mA)

Multi-functional analog output (Constant No. 44 is used to set the function
and constant No. 45 is used to set the multiplying factor.)
The output frequency or output current can be monitored. The Inverter is fac-
tory-set to output frequency monitoring.

Note

The standard Inverters are not provided with the multi-function analog
output.

Specifications

Chapter 4

Summary of Contents for 3G3EV-A2001-CUE
























































Reviews: