background image

9

Section 7 - Battery Installation

Battery Installation or Replacement

UWTC-1, UWTC-2, UWRTD-1, UWRTD-2

To install or replace the battery in your Connector/ 

Transmitter you must first remove the two screws located on the back side of 

your device. This will allow you to access the battery compartment.

 

Battery Replacement UWTC-1, UWTC-2, UWRTD-1, UWRTD-2

Battery Replacement

Your NB9 is equipped with a “C” size lithium power cell assembly. Omega 

Part Number: UWTC-BATT-NB. To install replacement battery assembly 

follow steps outlined here.
A.  Remove the two screws that secure 

the main circuit board from the 

probe head assembly.

B.  Tilt the front of the circuit board 

just high enough to allow you to 

unplug the connector that attaches 

the battery assembly to the bottom 

of the circuit board.

C. Remove the old power cell.
D.  Install your new battery assembly 

into the housing in the same 

position as the old battery was 

located.

E.  Connect the battery assembly 

connector to the mating connector 

on the bottom of the circuit board.

F.  Install the circuit board back into 

the housing and secure with the 

two screws you removed in step 

one.

G. Installation complete  

 

Battery Replacement

Battery Installation

7

BATTERY

+

ASSEMBLY
CONNECTOR

BATTERY
ASSEMBLY

ENCLOSURE

BOARD
CONNECTOR

CIRCUIT BOARD

MOUNTING SCREWS

Summary of Contents for UWRTD Series





















Reviews: