Page - 5
Page - 12
Using The RS-210-DP System
THE PARKING
LIGHTS WILL TURN
ON
THE ENGINE WILL CRANK
To Activate/Deactivate Remote Start:
Press & Release the transmitter “start” button twice
•
The lights will turn back on and remain on while the system is control-
ling the engine. The status light will then continue to flash slowly.
•
If the engine stalls, the system will make 3 more attempts to restart it.
•
The parking lights will turn on and the Status Light
will flash fast to confirm that starting has begun.
•
The sytem will then turn on the ignition circuit.
•
Within a few seconds the lights will turn off and the
starter will engage.
•
The engine will start, run, and the starter will be
disengaged.
Upon entering the vehicle place the ignition key in the switch and turn it
to the "On" position, pressing the brake pedal will deactivate the remote
start operation. Do not turn the key to the "Start" position!
If you decide not to drive your car after remote starting, you can simply
press & release the “start” button again to deactivate the remote start.
Otherwise, the system will “time-out” and turn off automatically after 10
minutes. NOTE: If there is no response when attempting to remote start
(and the system is not in valet mode), the system might be indicating that
a safety circuit is violated. This could mean that the hood is open, the gear
selector is not in park, or that the brake pedal is being pressed. Check
these safety circuits and retry.
When you leave your vehicle after driving, simply set the climate con-
trols for what you would like to have operating upon remote starting - the
heater, defroster or air conditioning.
Feature #2 “Tach Wire” , “Tachless”, or “Data Tach”
Starter Operation
Factory Default Setting
Tachless (
press
brake pedal 1x to program
)
Options:
Tach Wire (
press
brake pedal 2x to program
)
Data Tach (
press
brake pedal 3x to program
)
This feature selects the RS-210-DP processor’s method of determining the status of
the engine running during remote start operation. As explained in feature 5’s
description, “Tachless” mode has an associated base starter output time duration.
However, if the voltage fluctuation is detectable, the processor adjusts the starter
output time accordingly. When this feature is set for “Tach Wire” operation, the
base starter output increases to a maximum of 3 seconds, but the processor adjusts
the actual starter engagement time accordingly. Connecting and use of the “Tach
Wire” is the most reliable form of engine running information input, and its use is
recommended. Important: Before this feature is programmed, please refer to the
“Violet/White wire” section of the installation manual for proper wiring connec-
tion, and the Tach Learning Procedure. The “Data Tach” setting operates just like
the “Tach Wire” setting except it takes its reading from the D2D data port. Use of
this setting is determined by whether or not this feature is provided by the Databus
Interface module. If so, the Violet/White wire is not needed nor is the Tach Learning
Procedure Required. This feature should only be programmed by the installer.
Feature #1 Remote Start Activation Pulses
Factory Default Setting:
1 pulse
(
press
brake pedal 1x to program
)
Options:
2 pulses
(
press
brake pedal 2x to program
)
3 pulses
(
press
brake pedal 3x to program
)
4 pulses
(
press
brake pedal 4x to program
)
This feature allows you to choose the number of pulses required on the White/Blue
activation wire to activate the remote start feature. This allows you to activate the
remote start with external devices. For example, you can connect this wire to a
factory installed keyless entry system. You can repurpose the factory lock button so
that multiple presses will activate the remote start. With any of the optional settings,
each 2nd, 3rd, or 4th pulse must occur within a 5 second window of the previous
pulse. This feature should only be programmed by the installer.
THE PARKING
LIGHTS WILL FLASH
TWICE THEN TURN
ON FOR 30 SECONDS
THE DOORS WILL UNLOCK
To Unlock the Vehicle's Doors:
Press & Hold the transmitter START button for 3 seconds
•
The parking lights flash twice then stay on for 30
seconds to confirm unlocking. The Status Light will turn
off to indicate that the system is in an UNLOCKED state.
