background image

                                                                                                         Temperature/Event Adapter

       5

Press and hold the 

             

R E C O R D

 button until the record display appears. The four

recording modes can be scrolled and changed by using  

              

S T A T U S

 button:

1. 

Record information to memory only.

 This

    option stores information into the Service
    Logger memory. No printer or computer
    connection is required for this function.

2. 

Record information to a printer.

 This option

    does not store information into memory but
    does print each sample as it is 

recorded

 to a

    printer. This is referred to as REAL TIME 
    PRINTING. 

A printer must be connected for

    this function! 

If no printer is connected, or if

    the printer is 

off-line

, or if the printer is out of

    paper an error message will be displayed to
    alert the user to a problem. Switching to this
    option will 

terminate recording

 if the Service

    Logger was set to record previously.

3.

 Record information to memory and to a

    printer. 

This is a combination of options 1

    and 2. Information is stored in memory and at
    the same time each sample is 

recorded

 to a

    printer. As in option 2 a 

printer must be

    connected

 and functioning or an error message

    will be displayed.

4. If a recording is in progress, this option will

    terminate all

 

recording functions

. This

    option may also be used if the user decides to
    terminate a recording session and return to the
    operating mode. In order to terminate a recording

    press the 

                   

M E N U

               

 

E N T E R

 button again at this time.

Press the 

             

R E C O R D

 button after selecting the

recording mode. This will display the starting
time of the recording. The display will show the
starting time of the last recording and allow the

RECORD ON, REAL

TIME PRINT OFF

RECORD OFF, REAL

TIME PRINT ON

RECORD ON, REAL

TIME PRINT ON

RECORD OFF, REAL

TIME PRINT OFF

DAY  HOUR  MIN

FRI      15      16

Summary of Contents for OM-60-MOD-TE













Reviews: