background image

8

 

SUPPORT LEGS 

 

 

The cookers are supplied with four transit supports (one for each corner). 

 

Four support legs are supplied separately and are fitted on location to the four corners of the lower support frame. Each 
support leg is pushed over the relevant transit support until flush with the support frame. 

 

Each leg is adjusted by screwing the lowe r section in or out as required for fitting to a 900mm bench height. For lower bench 
tops adjust the height of the legs to 180mm so the hob is located 10mm above the horizontal combustible surface, ref. 
AS/NZS 5601. 

 

 

Fig. 06 

 

 
Legs should be installed with the appliance close to its final 
destination, as the legs are not designed for excessive force 
and will snap off if too much side force is exerted on them 
(dragging along or angled too much). When fitting, try to keep 
the appliance as close to a horizontal position as possible. Use 
of a pallet jack is recommended. 
If the legs are not used and the cooker is mounted onto a 
plinth, four transit supports allow for clearance. 

With the legs fitted, the splash-back can be fitted. 
Follow the instructions shown in Fig. 07. 

 

 
 
 
 
 
 
 
Fig 07 

Summary of Contents for OF916FKXP























Reviews: