and pause to indicate which protected zone was violated while the system is still
armed, after it’s disarmed, and until the vehicle’s ignition is turned on. The
system’s Zone Violation memory can store two consecutive zone violations. If
there have been multiple violations, the Status Indicator Light will replay the two
most recent violations in the order in which they occurred.
9) 2 Red Flashes / Pause = System was triggered by an open hood or trunk.
10) 3 Red Flashes / Pause = System was triggered by an open door.
11) 4 Red Flashes / Pause = System was triggered by the sensor.
Starting System Status:
The primary function of the Status Indicator
Light is to indicate the status of the remote starting system:
12) Off = The remote starter system is off and in standby mode. The security
system is disarmed and not performing automatic functions.
13) Flashing Slow Green = The engine is running after remote starting.
14) Flashing Fast Green = A remote start command has been received, and the
system is in the process of starting the engine.
Remote Starting Diagnostics:
Whenever the system is placed into Valet
Mode, the Status Indicator Light illuminates solid Red. However, when this
occurs, the Status Indicator Light will flash Red, then 1 to 6 Green flashes before
resuming solid Red. This indicates why the engine stopped running from the last
previous remote starting.
15) Red / 1 Green Flash / Red = Programmed run time expired.
16) Red / 2 Green Flashes / Red = Brake was pressed or hood opened.
17) Red / 3 Green Flashes / Red = Engine stalled or bad tach signal.
18) Red / 4 Green Flashes / Red = Received transmitter command to stop.
19) Red / 5 Green Flashes / Red = Gear selector removed from “park”.
20) Red / 6 Green Flashes / Red = Security system triggered or low voltage.
Combination Indications:
These indications occur when security and
remote starting operations are, or have been, simultaneous.
21) Slowly Alternates Red & Green = Full Valet Mode (page 22).
22) Solid Green w/ Red Flash = Security Armed with Starting Valet Mode.
23) Solid Red w/ Green Flash = Remote starter system engaged with security
system in Valet Mode.
24) Rapidly Alternates Red & Green = Remote starter system engaged with
security system armed.
25) Slow Flashing Green w/ 2 to 4 Red Flashes = This indication is during remote
start operation after disarming the alarm, and shows that the pre-
viously Armed alarm was activated and reset prior to the remote
starting. The Red flashes are the Zone Violation (previous page),
occurring with the “engine running”
indicator.
Page 24
VEHICLE RECOVERY
Your system is equipped with three separately programmable Vehicle Recovery
protection features, which also provide Anti-Carjacking protection. The Vehicle
Recovery operation may be selectively activated by the ignition, by an open door,
or by the transmitter or Echo transceiver.
How It Works:
Once the Vehicle Recovery process has begun, the user has 53 seconds to
cancel the process by pressing the Valet Switch once. If Vehicle Recovery is not
cancelled, 53 seconds after being activated the siren will begin to chirp for 7
seconds to alert the user that the system is about to enter into an alarm condition.
If the Vehicle Recovery process is not cancelled before the 60 second count-
down expires, the system will enter an alarm condition, sounding the siren and
flashing the parking lights. The stater interrupt will engage 30 seconds after
this occurs, or immediately should the ignition be turned off in the meantime.
Once the system enters the alarm condition, it will not respond to the trans-
mitter/transceiver, nor will the system reset automatically after 60 seconds.
Once in the alarm condition, the Vehicle Recovery Protection can only be dis-
engaged by:
Step 1 Turning the vehicle’s ignition off.
Step 2 Turning the ignition back on.
Step 3 Within 5 seconds, perform an Emergency Override using the Valet
Switch.
Level #1: Vehicle Recovery activated by the vehicle’s ignition:
The Vehicle Recovery process is started every time the vehicle’s ignition is
turned on. This is programmable feature #14.
Level #2: Vehicle Recovery activated by an open door:
The Vehicle Recovery process is started by a door of the vehicle being opened,
but only if the ignition is on when the door is opened. This is programmable
feature #15.
Level #3: Vehicle Recovery activated using a remote control:
The Vehicle Recovery process is started by pressing holding the transmitter’s or
Echo transceiver’s “
lll
” (or, “Auxiliary Output #3”) button for 3 seconds, but
only if the vehicle’s ignition is on. This is programmable feature #16.
Page 25
