background image

Page 19

THE PARKING LIGHTS

WILL ILLUMINATE*

To Activate Remote Starting:

THE ENGINE

STARTS

To remote start the vehicle:
1- Press and release together the transmitter or Echo transceiver’s “Arm/Lock”

and “Disarm/Unlock” buttons.  The system will respond first by rapidly
flashing the Status Indicator Light Green, then by turning on the ignition and
flashing the parking lights once.

2- The starter will engage until the engine runs; 10 seconds later the parking

lights will illuminate steady during the period that the engine is running
from being remotely started. (having them flash instead is an option).

If the Echo transceiver is used to activate remote engine starting feature, it

will further sequence status indications beyond what the system does in the
vehicle.  When the Echo is used for remote starting:
• It will play a musical melody, and the “start” icon, puffs of smoke, appear

behind the vehicle (5 different musical melodies are programmable).

• Once the engine has started, when the vehicle’s parking lights come back on

the “start: icon’s puffs of smoke will change to appearing sequentially.

• When the engine stops running, whether by safety condition or transceiver

command, a different musical melody is played, and the “start” icon disap-
pears.  If a safety circuit stops the engine, the “crossed out key” icon will
momentarily appear (but not if the transceiver’s command stops the engine).

• If a safety circuit prevents the starting attempt, the “engine stopped” melody

will play, and the “crossed out key” icon will appear.

Once the engine has been remotely started, it will run for 10 minutes (an

optional 20 minute setting may be programmed).  To remotely stop the engine
again press and release together the “Arm/Lock” and “Disarm/Unlock”  buttons.
The system will stop the engine, and extinguish the parking lights.

When leaving the vehicle before remote starting, remember to set the climate
controls to the desired heating or air conditioning settings.

* FLASHING PARKING

LIGHTS IS OPTIONAL

AND

AND

Press & Release the “Arm/Lock” Button (     )  and the “Disarm/Unlock”
Button (     ) together

J

U

Feature #4

                    Last Door Arming

 

                                                          

(Factory Default Setting Off)

This feature configures the system to automatically Arm itself 30 seconds

after the vehicle’s last door is closed.

Programming Last Door Arming:

Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and

released four times.  The system’s response will be four siren chirps, and the
Status Light flashing four times, pausing, then repeating.  Within 10 seconds,
press and release the transmitter/transceiver’s "Arm/Lock" button to turn on Last
Door Arming (the siren will chirp once) or the "Disarm/Unlock" button to turn
off Last Door Arming (the siren will chirp twice).

Feature #3

                3 / 45 Second Arming Delay
    

    (Factory Default Setting  3  Second)

This feature determines how long after the Arming confirmation chirp that

the system becomes fully Armed.  The Arming Delay applies to the system
Arming regardless if it occurs from using the transmitter/transceiver, Last Door
Arming or Automatic Rearming.

Programming 3 / 45 Second Arming Delay:

Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and

released three times.  The system’s response will be three siren chirps, and the
Status Light flashing three times, pausing, then repeating.  Within 10 seconds,
press and release the transmitter/transceiver’s "Disarm/Unlock" button to config-
ure the system with a 45 second Arming Delay (the siren will chirp once) or the
"Arm/Lock" button to configure the system with a 3 second Arming Delay (the
siren will chirp twice).

Page 30

Feature #2

         30 or 60 Second Alarm Duration

       (Factory Default Setting 30 Seconds)

This feature allows the option of a 30 or 60 second Alarm Duration, which is

when the system has been activated into an Alarm state, sounding the siren and
flashing the parking lights.

Changing the Alarm Duration:

Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and

released twice.  The system’s response will be two siren chirps, and the Status
Light flashing two times, pausing, then repeating.  Within 10 seconds, press and
release the transmitter/transceiver’s "Arm/Lock" button to set the Alarm Dura-
tion for 60 seconds (the siren will chirp once) or the "Disarm/Unlock" button to
set the Alarm Duration for 30 seconds (the siren will chirp twice).

Summary of Contents for Crime Guard 850i4



























Reviews: