background image

The Last Door Arming process:

1- When the vehicle’s ignition has been turned off, the system waits until a door

is opened.  When the door is closed, or when the last door is closed when
more than one door is opened, the siren will chirp twice, the parking lights
will flash twice, and the Status Indicator Light will begin flashing Red rap-
idly.  The Last Door Arming countdown has begun.

2- Thirty seconds later the siren will again chirp twice, the parking lights will

again flash twice, the starter interrupt will engage, and the Status Indicator
Light will begin flashing Red slowly.  If programmed , the vehicle’s doors
will also lock.*  Three seconds after these actions occur, the system is fully
armed.

Notes:

• If the remote transceiver was last used to operate the system, when Last Door

Arming is used to arm the system the transceiver will chirp twice and show the
“ARM” icon when system becomes fully armed 30 seconds after the last door
is closed.  If the doors are programmed to also lock*, the “locked” icon will also
appear when this occurs.

• If a door is reopened during the thirty second period between the first and

second set of double chirps, the countdown will stop and reset.  When the
reopened door is closed again, the 30 second countdown starts over again at
the beginning.

• Last Door Arming is separate from, and does not effect the operation of arming

by using the transmitter or transceiver.

• All protected points must be closed or otherwise in a non-violated state for the

Last Door Arming sequence to start.  Unlike active arming from the transmit-
ter or transceiver, the system can not bypass an open or detected zone and arm
itself.

To temporarily prevent the system from arming itself:

• Place the system into Alarm Valet Mode using the Valet Switch (page 21).
• Leave a vehicle door open.  Although this varies depending on the vehicle, in

most cases turning on the interior light will be detected by the system as an open
door.

• Although the system will not Last Door Arm while the ignition is on, leaving

the ignition key turned on without the engine running  is not recommended.

The Last Door Arming feature may include, if desired, the automatic locking of
the vehicle’s doors when the system arms itself.*

Page 8

* An optional doorlock interface must be installed

Page 41

required to use this feature.  To program the feature, follow Steps 1 to 4 on page
27; at Step 4 the Valet Switch will be pressed and released twenty nine times.  The
system’s response will be twenty nine siren chirps, and the Status Light flashing
twenty nine times, pausing, then repeating.  Within 10 seconds, press and release
the transmitter’s "Arm/Lock" button to configure the system for Tachless
operation (the siren will chirp once) or the "Disarm/Unlock" button to configure
the system  for Tach Wire operation (the siren will chirp twice).

Your Crime Guard 850i

 system is capable of being operated by as many as

four controllers; these can be any combination of standard Crime Guard transmitters
or Omega Echo transceivers.  Regardless of which, the transmitter or transceiver
must be encoded, or programmed, to the system in order to operate it (excepting
the originals, which were programmed at the factory).  This programming
procedure is identical for a transmitter or Echo transceiver.  To program
additional or replacement transmitters or transceivers, follow this procedure:

Have all of the transmitters or transceivers at hand (when one is programmed, all
others are erased).

Step 1 Turn the vehicle’s ignition “on”.

Step 2 Within 5 seconds of turning "on" the ignition, press the Valet Switch 5

times. The siren will chirp once, confirming that the system is ready to
learn a transmitter.

Step 3 Within 10 seconds press and release the “Arm/Lock” button (the “locked

padlock” graphic).  The siren will chirp once, confirming that the system
learned the transmitter.

Step 4 Repeat the previous step for each transmitter or transceiver which is to

operate the system.

Only the “Arm/Lock” button is pressed in programming; when it is learned all of
the other buttons’ functions are automatically assigned.  The system will remove
itself from the programming mode if 10 seconds expire without its receiving a
signal, if the ignition is turned “off”, or upon four transmitters or transceivers
being programmed into the system.

Please note that programming a transmitter to the system will activate the

PROGRAMMING   TRANSMITTERS

OR  ECHO  TRANSCEIVERS

Summary of Contents for Crime Guard 850i4



























Reviews: