Page 11
Safety Disarm Feature:
Pressing and releasing the “Disarm/Unlock button while the system is
activated in the alarm condition will disarm the system, but the doors will re-
main locked. This is the “Safety Disarm” feature, which allows the vehicle to
remain secure, even though an activated system has been disarmed. Safety Dis-
arm will also cancel Automatic Rearming (if it is programmed to operate). This
feature is also very useful when the vehicle is exposed to environmental condi-
tions such as storms, trains or heavy vehicles, which may cause false activations.
Safety Disarm is a temporary “one time” operation which occurs only while
the system is activated. To remotely unlock the doors after a Safety Disarm,
simply press the “Disarm/Unlock” button again.
Upon Disarming the System will:
• The siren will chirp once (or three times if an alarm activation occurred)
unless the silent disarming procedure is followed.
• The parking and dome lights will illuminate for 30 seconds (5 seconds is
optional) unless the vehicle’s ignition is turned on. If the system has been
activated, the parking lights will flash 3 times before illuminating.
• The doors will unlock, either all doors or driver’s door only.*
• The starter interrupt will disengage.
• The Status Indicator Light will show one of these features or conditions:
-Flashing Red rapidly = Automatic Rearming feature is in progress.
-Off = System disarmed (Automatic Rearming feature not selected).
-Flash Red /Pause = Indicates violated zone if system has been activated.
Upon Disarming with the Echo Transceiver, it will:
• The transceiver will chirp once (or three times if the system was activated).
• The “DISARM” icon will appear.
• The “unlocked lock” icon appears, confirming that doors have unlocked.
• The number of operating transmitters or transceivers is briefly displayed.
When Disarming and Driver’s Door Priority unlocking is utilized, if the “Un-
lock/Disarm” neither the system nor the transceiver will repeat the Disarming
confirmation indicators. As the system does not transmit a signal to the trans-
ceiver, its “in range” icon will disappear, and then reappear again when the sys-
tem is next Armed, or other remote function is used.
Activation Alert:
If the system experiences an alarm condition and resets itself, upon disarming
the siren will chirp three times and the parking lights will flash three times instead
Page 38
Feature #24
Door Lock/Unlock Pulse Duration
(Factory Default Setting .8 Second)
This feature, for the installer’s use, offers the selection of a .8 second or a 3
second pulse duration of the system’s doorlock outputs. Certain vehicles have
power doorlocking systems which are vacuum operated, and thus require a
longer output pulse from the Crime Guard system. While use of this feature is
determined by the type of vehicle the system is installed in, this feature does save
the owners of such vehicles the added expense of a special adapter.
Programming Door Lock/Unlock Pulse Duration:
Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and
released twenty four times. The system’s response will be twenty four siren
chirps, and the Status Light flashing twenty four times, pausing, then repeating.
Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock"
button to configure the doorlock pulse for .8 second (the siren will chirp once)
or the "Disarm/Unlock" button to configure the doorlock pulse for 3 seconds (the
siren will chirp twice).
Disarming the system with every press of that same button. When this feature
is programmed for “1 Button Operation”, the system’s operation with the
included transmitter and/or Echo pager is:
“Locked Lock” button = Arm or Disarm (alternates)
“Unlocked Lock button = Auxiliary #2 output
“
II
” button = Auxiliary #3 output
“
III
” button = nothing (open for other receiver unit)
“Locked Lock” & “Unlocked Lock” buttons together = remote start
Programming Transmitter 1 or 2 Button Operation:
Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and
released twenty three times. The system’s response will be twenty three siren
chirps, and the Status Light flashing twenty three times, pausing, then repeating.
Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock"
button to configure the system for “1 Button Operation” (the siren will chirp
once) or the "Disarm/Unlock" button to configure the system for “2 Button
Operation” (the siren will chirp twice).
Feature #25
Double Unlock Pulse
(Factory Default Setting OFF)
This is another power door lock-related feature for the installer’s use; some
newer vehicles require a double pulse to remotely unlock the doors and/or to
disarm a factory-equipped security system.
