background image

To Disarm the System:
Press & Release the “Disarm/Unlock” Button (     )

THE SIREN WILL CHIRP

ONCE TO CONFIRM
DISARMING

REMOTE DISARMING BY TRANSMITTER OR TRANSCEIVER

 J

THE PARKING AND

DOME LIGHTS WILL

ILLUMINATE

TO CONFIRM

DISARMING

Page 10

• Pressing “Disarm/Unlock” will disarm the system, leaving the doors locked,

stopping both system’s alarm condition (leaving it disarmed) and the
transceiver’s chirping.

• Pressing and releasing any of the three other buttons will simply stop the

transceiver’s chirping, but leave the security system still sounding in its
alarm state.

The remote transceiver will display the flashing icon indicating the violated zone,
while the system is disarmed, until the ignition switch is turned on.

There are three methods of Disarming the security system:

1- The first method is to press and release the transmitter or transceiver’s

“Disarm/Unlock” button to disarm the system. This is the normal method.

2- The second method is to press and release the transmitter or transceiver’s “

II

button twice within 5 seconds.  This is “silent Disarming”.

3- The third method is for emergencies, should the transmitter become lost or

inoperable.  This is the “Emergency Override”, and uses the ignition key and
the Valet Switch.

 

DISARMING THE SYSTEM

THE DOORS WILL UNLOCK;

Either All or Drivers*

With Driver’s Door Priority, again Press & Release the “Disarm/Unlock”
Button (     ) to unlock the remaining doors

J

*An optional doorlock interface, in either standard form or driver’s door priority form, must be installed

Page 39

Feature #27

     Gasoline Or Diesel Engine

(Factory Default Setting Gasoline)

This feature changes the system's timing of the ignition and starter output

sequence for remotely starting vehicles with a diesel engine.

Programming Gasoline or Diesel Engine:

Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and

released twenty seven times.  The system’s response will be twenty seven siren
chirps, and the Status Light flashing twenty seven times, pausing, then repeating.
Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock"

Feature #26

    Total Closure Lock Output

         

        (Factory Default Setting OFF)

If the vehicle is has an existing total closure feature, this programmable

feature gives the installer the option of interfacing the system to operate this
feature.  Typically, this option would close all windows and the sunroof, in
addition to locking the doors, when arming the system.  Consult with the in-
staller on this option, as the vehicle must be properly equipped to utilize this
system feature.  Turning this feature on changes the door lock output pulse to a
28 second duration.
Note: When using this feature, upon Arming the system, should the “Disarm/
Unlock” button be pressed during the 28 second lock output period, the output
will stop only- the system will not Disarm.  Pressing the button again will Disarm
the system, and at any time after the 28 second lock output period.

Programming Total Closure Lock Pulse:

Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and

released twenty six times.  The system’s response will be twenty six siren chirps,
and the Status Light flashing twenty six times, pausing, then repeating.  Within
10 seconds, press and release the transmitter/transceiver’s "Arm/Lock" button to
configure the 28 second door lock pulse for total closure (the siren will chirp
once) or the "Disarm/Unlock" button to configure the short door lock pulse (the
siren will chirp twice).

Programming Single or Double Unlock Pulse:

Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and

released twenty five times.  The system’s response will be twenty five siren
chirps, and the Status Light flashing twenty five times, pausing, then repeating.
Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock"
button to configure the double unlock pulse (the siren will chirp once) or the
"Disarm/Unlock" button to configure the single unlock pulse (the siren will chirp
twice).

Summary of Contents for Crime Guard 850i4



























Reviews: