Arming Bypass:
Upon arming, if any system sensing circuit is inoperable,
that circuit only will automatically be bypassed. When an unsecured sensing circuit
is in a bypassed state, all other normally operating circuits will be protected. Should
the bypassed circuit become secured, it will automatically be reinstated for
protection 5 seconds later. When certain protection circuits are bypassed, such as
the hood/trunk and impact sensor, and the system is armed, it will indicate this by
chirping the siren three time and flashing the parking lights three times instead of
the normal arming indication of one chirp and one flash.
For example, should the trunk be open, you can still arm the system with the
transmitter, and in this case the arming indicator will be 3 siren chirps and 3 parking
light flashes. Arming Bypass will only operate when arming the system with the
transmitter.
Sensor Bypass:
When arming the system with the transmitter, you may
conveniently and easily temporarily deactivate the impact sensor without affecting
the system’s other sensing circuits. To deactivate the sensor, arm the system by
pressing the “arm/lock” button, then press and release the transmitter’s “
II
” button
within three seconds.
You will hear a second siren chirp confirming that the security
system has armed without the sensor protecting the vehicle. The next time the system
is armed normally with one “arm/lock” button press, the sensor will again be part
of your protection.
Automatic “Last Door Arming” of the System
The system can also be programmed to automatically arm itself, and in this
process, to lock or not lock the doors. When this feature is utilized, closing the
vehicle's last door will cause the siren to chirp once, the parking and interior lights
to flash once and the Status Light to start rapidly flashing red. Thirty seconds later
the siren will chirp again and the lights will flash again, the doors will lock (which
is separately programmable) and the Status Light will slow to a steady red flash,
confirming that the security system is fully armed. If a point of entry is reopened
before the single siren chirp at 30 seconds, the Last Door Arming process stops, and
will reset to start over when the point of entry is again closed. All protected entries
The system’s separate “arm/lock” and “disarm/unlock” button design allows
repetitive operation- if already armed, pressing the “arm/lock” button will simply
rearm the system, and vice versa when pressing the “disarm/unlock” button.
Page - 8
Option:
On (
press
“arm/lock” button to program
)
When this feature is turned on, if one of the vehicle's doors is open at the time that
the system is armed via the transmitter, the siren will chirp 3 times and the parking
lights will flash 3 times instead of once.
Feature #21 Remote Start Activation
Factory Default Setting
“
III
”
button 2 times in 5 seconds
(
press
“arm/lock” button to program
)
Options:
“
III
”
button 1 time (
press
“disarm/unlock” button to program
)
Lock & Unlock
(
press “
II
” button to program
)
This feature changes how the remote start feature is activated using the transmitter.
Page - 33
Feature #22 Remote Start Run Time
Factory Default Setting
10 Minutes
(
press
“disarm/unlock” button to program
)
Options:
5 Minutes
(
press
“arm/lock” button to program
)
15 Minutes
(
press “
II
” button to program
)
20 Minutes
(
press
to program
)
This feature sets the period of time that the engine will run after being remotely
started. If the engine is not stopped by a transmitter command or a safety circuit
violation, the engine will automatically stop upon the expiration of the selected time
period. Caution: The remote engine starting feature should NEVER be used
when the vehicle is parked in an enclosed structure or garage.
Feature #23 Steady/Flashing Lights During Remote Start
Factory Default Setting
Steady (
press
“arm/lock” button to program
)
Option:
Flashing (
press
“disarm/unlock” button to program
)
This Feature configures the system's operation of the vehicle’s parking lights when
the engine is running after it has been remotely started. The factory default setting
has the parking lights illuminating steady during the engine run time; the other
setting flashes the parking lights on and off during the engine run time.
