background image

4

ALARM2 HIGH: Upper limit alarm 2 (display according to the setting in ALARM mode) 

4.0 

ALARM2 LOW: Lower limit alarm 2 (display according to the setting in ALARM mode) 

4.0 

ALARM3 HIGH: Upper limit alarm 3 (set OUT2 to ALARM mode and it will display according to the 

setting in ALARM mode) 

4.0 

ALARM3 LOW: Lower limit alarm 3 (set OUT2 to ALARM mode and it will display according to the 
setting in ALARM mode) 

4.0 

ALARM1 HIGH PEAK: High peak value 1 
ALARM1 LOW PEAK: Low peak value 1 
ALARM2 HIGH PEAK: High peak value 2 
ALARM2 LOW PEAK: Low peak value 2 
ALARM3 HIGH PEAK: High peak value 3 (display when OUT2 is set to alarm mode) 
ALARM3 LOW PEAK: Low peak value 3 (display when OUT2 is set to alarm mode) 
OUT1: Display and adjust output value of 1

st

 output group 

0.0 

OUT2:  Display  and  adjust  output  value  of  2

nd

  output  group  (display  when  OUT2  is  set  to 

Heating/Cooling Mode) 

0.0 

OUT1 MAX: Upper limit % of 1

st

 output group (perform linear calculation again) 

100.0 

OUT1 MIN.: Lower limit % of 1

st

 output group 

0.0 

OUT2 MAX: Upper limit % of 2

nd

 output group (display when OUT2 is set to Heating/Cooling Mode) 

100.0 

OUT2 MIN: Lower limit % of 2

nd

 output group (display when OUT2 is set to Heating/Cooling Mode) 

0.0 

CT1: Display CT1 current (display when external CT is connected to CT1) 
CT2: Display CT2 current (display when external CT is connected to CT2) 

press 

  to return to target temperature setting. 

Initial Setting Mode

Parameter Settings: 

Display 

Description 

Factory Setting

INPUT: Set input type (refer to “Temperature Sensor Type & Temperature Range Chart” for the 
selection of Thermocouple or Platinum Resistance types.)   

PT 

TEMP. UNIT: Set temperature unit  /

℉(

it wil not be displayed when in analog input mode

 

TEMP. HIGH: Set up upper temperature limit (the upper limit setting is different for different types of 
sensor)   

850.0 

TEMP. LOW: Set up lower temperature limit (the lower limit setting is different for different types of 
sensor) 

-200.0

CONTROL: Select control modes ( 5 different modes: ON-OFF, PID, MANUAL, FUZZY and 2PID) 

PID 

CONTROL SV provides 4 different options: CONS; PROG; SLOP; and REMO. REMO mode is 
available when REMOTE function is added.   

CONS 

WAIT SV: Set up waiting temperature 

display when in programmable control

 

WAIT TIME: Set up waiting time

display when in programmable control

 

SLOP: Set up start slope 

display when in programmable control

 

PATTERN: Select pattern to be edited (display when in programmable control, there are 16 patterns 

and each pattern includes 16 steps. Setting parameters are OFF, SAVE, 0~F.) 

OFF 

TUNE: Select AT or ST (display when in PID/2PID control mode) 

AT 

SELECT HEAT/COOL: Select heating, cooling or dual output heating and cooling 

H1H2 

ALARM1 SET: Set up Alarm 1 mode (refer to “Alarm Output” for more setting on modes) 

ALARM1 OPTION:

 

Set up Alarm 1 options    (refer to “Alarm Output” for more setting on modes) 

ALARM1 DELAY: Set up Alarm 1 delay (refer to “Alarm Output” for more setting on modes) 

ALARM2 SET: Set up Alarm 2 mode (refer to "Alarm Outputs") 

ALARM2 OPTION: Set up Alarm 2 options (refer to “Alarm Outputs” ) 

ALARM2 DELAY: Set up Alarm 2 delay (refer to “Alarm Outputs” ) 

ALARM3 SET: Set up Alarm 3 mode (refer to "Alarm Output")(display when OUT2 is set to ALARM 
mode) 

ALARM3 OPTION: Set up Alarm 3 options (refer to "Alarm Output") (display when OUT2 is set to 
ALARM mode) 

Summary of Contents for CN16D3-R-AC





























Reviews: