background image

6

PV OFFSET: Adjust input compensation of PV 

0.0 

PV GAIN: Adjust input gain of PV 

0.000 

SV SLOPE: Set up rising slope (when CRTS = SLOP) 
ANALOG OUT1 MAX.: Adjust upper limit compensation for analog Output 1 
(1scale = 1μA; 1scale = 1mV)   

ANALOG OUT1 MIN.: Adjust lower limit compensation for analog Output 1 
  (1 scale = 1μA; 1scale = 1mV) 

ANALOG OUT2 MAX.: Adjust upper limit compensation for analog Output 2 
  (1scale = 1μA; 1scale = 1mV) 

ANALOG OUT2 MIN.: Adjust lower limit compensation for analog Output 2 
  (1scale = 1μA; 1scale = 1mV) 

RETRANSMISSION MAX.: Adjust upper limit compensation for Retransmission 
(1scale = 1μA) (display when a Retransmission Card is connected to 

CND3

RETRANSMISSION MIN.: Adjust lower limit compensation for Retransmission 
(1scale = 1μA) (display when a Retransmission Card is connected to 

CND3

REMOTE GAIN: Adjust Remote gain (When CRTS = REMO) 

REMOTE GAIN: Adjust Remote compensation (When CRTS = REMO) 

REMOTE LOW: Remote lower limit (When CRTS=REMO) 

REMOTE HIGH: Remote higher limit (When CRTS=REMO) 

100 

EVENT1: Set up EVENT1 function (display when a Event Card is connected to EVENT1) 

OFF 

EVENT2: Set up EVENT2 function (display when a Event Card is connected to EVENT2) 

OFF 

EVENT3: Set up EVENT3 function (display when a Event Card is connected to EVENT3) 

OFF 

PID mode: Any of the 6 PID groups can be selected. When set to AUTO mode, the program will automatically select the PID group that is 
the closest to the target temperature. 
Select 0~5 group of PID and execute AT function, the system will automatically load P; I; D and IOF parameters into the selected PID 
group.   

Select the n

th

 PID (n = 0 ~ 5)               

  press 

  to set 0 ~ 5

th

 PID parameters 

  Set up the 0

th

 PID temperature value       

press 

 

 

  ~ 

  Set up the 5

th

 PID temperature value 

      press 

 

  Set up the 0

th

 proportional band value 

  ~ 

  Set up the 5

th

 proportional band value 

  Set up the 0

th

 Ti value 

  ~ 

  Set up the 5

th

 Ti value 

  Set up the 0

th

 Td value 

  ~ 

  Set up the 5

th

 Td value 

  Set up the 0

th

 PID integral deviation 

Press 

  to set the parameters in 

“Regulation Mode” 

  ~ 

  Set up the 5

th

 PID integral deviation 

Press 

  to set the parameters in 

“Regulation Mode” 

Programmable Editing: set 

  to 

  or 

  and set 

  to 

.   

  Select desired editing pattern number 0~F                                              press 

  to set the desired editing pattern number 0~F 

If the setting is OFF, leave the editing pattern page and go to 

  to continue with the setting.

 

Edit the temperature of step No.0 of pattern No. 0 

    press 

 

  ~ 

 

Edit the temperature of step No.0 of pattern No. 15

Edit the time of step No.0 of pattern No. 0 (time unit: 

hh, mm) 

Edit the time of step No.0 of pattern No.15 (time unit: 

hh, mm) 

  ~ 

  Set up step 0~15 in order 

  ~ 

  Edit the temperature of step No.15 of pattern No.0 

  ~ 

  Edit the temperature of step No.15 of pattern No.15

Edit the time of step No.15 of pattern No.0 

Edit the time of step No.15 of pattern No.15 

  Seelect the actual required steps for executing 

pattern No.0 

  ~ 

  Seelect  the  actual  required  steps  for  executing 

pattern No.15 

  Set up the additional cycle (0~199) for pattern No. 

0 execution   

  ~ 

  Set up the additional cycle (0~199) for pattern No. 

15 execution 

  Set up the link pattern of pattern No.0 (0~F; 

END; STOP)             

Press 

  to return to the 

selection of desire editing pattern and number.

  ~ 

  Set up the link pattern of pattern No.15 (0~F; 

END; STOP)             

Press 

  to return to the 

selection of desire editing pattern and number

Summary of Contents for CN16D3-R-AC





























Reviews: