Olympus CF Q160AL/I Instructions Manual Download Page 44 | Manualshive

Page: 44 / 74

background image

40

Chapter 3 Cleaning, Disinfection and Sterilization Procedures

EVIS EXERA GIF/CF/PCF TYPE 160 Series REPROCESSING MANUAL

Figure 3.22

Use the channel cleaning brush (BW-17K) to brush the
instrument channel of the GIF-XTQ160. If the BW-17K is not
used on this endoscope, effective cleaning of the instrument
channel will not be possible.



Brushing the instrument/suction channel in the insertion
tube (location A) (except for GIF-XTQ160)

1.

Straighten the endoscope’s bending section. Grip the channel cleaning
brush (BW-20T) at a point 3 cm from the bristles.

2.

Insert the channel cleaning brush (BW-20T) at a 45



angle into the opening

located in the side wall of the suction cylinder as illustrated by A in Figure
3.22. Using short strokes, feed the brush through the insertion tube until it
emerges from the distal end of the endoscope.

3.

Clean the bristles with your fingertips in the detergent solution. Carefully pull
the brush out through the channel.

4.

Clean the bristles in the detergent solution again.

5.

Repeat until all debris is removed.

Suction cylinder

Instrument channel port

Suction connector

A

A

C

B

D

B

«
...
42
43
44
45
46
...
»

Summary of Contents for CF Q160AL/I











































































Reviews:

No comments

Related manuals for CF Q160AL/I

Brand: MacDon Pages: 2

Brand: MacDon Pages: 214

Brand: MacDon Pages: 32

Brand: ICS ELECTRONICS Pages: 6

Brand: Yamaha Pages: 50

Brand: A&D Pages: 30

Movie FL Black E27 Flaps

Brand: Qazqa Pages: 2

Brand: MacDon Pages: 46

Brand: MacDon Pages: 82

Brand: Mac Medical Pages: 2

Brand: MACDEV Pages: 8

Mentor Touch ET750

Brand: MAC TOOLS Pages: 24

Brand: MA lighting Pages: 10

Brand: Madsen Pages: 206

Brand: OHAUS Pages: 84

Brand: PAS Systems International Pages: 24

MARK V Alcovisor

Brand: PAS Systems International Pages: 20

Brand: PARRY Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands