Olympus CF Q160AL/I Instructions Manual Download Page 41

Page: 41 / 74

Chapter 3 Cleaning, Disinfection and Sterilization Procedures

EVIS EXERA GIF/CF/PCF TYPE 160 Series REPROCESSING MANUAL

Wait 30 seconds, or until the covering of the bending section contracts to its
pre-expansion size. Disconnect the leakage tester’s connector cap from the
venting connector.

10.

Thoroughly dry the leakage tester.

3.5

Manual cleaning

After completing the leakage test, perform manual cleaning according to the
procedures described below.

Equipment needed

Prepare the following equipment:

To prevent damage to the endoscope, never immerse it
together with objects other than the reprocessing
accessories.

• Personal protective equipment
• Soft brush
• Clean, lint-free cloths
• Large basins
• Detergent solution
• Clean water
• Suction pump

• 30 cm

(30 ml) syringe

• Suction cleaning adapter

(MH-856)

• Channel plug

(MH-944)

• Injection tube

(MH-946)

• Channel cleaning brush

(BW-20T)

• Channel cleaning brush

(BW-17K for GIF-XTQ160 only)

• Channel-opening cleaning brush

(MH-507)

• Auxiliary water tube

(MAJ-855 for endoscopes with
auxiliary water feeding only)

Summary of Contents for CF Q160AL/I











































































Search results

Summary of Contents for CF Q160AL/I

Reviews:

Olympus CF Q160AL/I, Instructions Manual, Page: 41 / 74

Search results

Summary of Contents for CF Q160AL/I

Reviews: