![background image](http://html.mh-extra.com/html/olympia/carrera-de-luxe-md/carrera-de-luxe-md_service-manual_732750060.webp)
Reassembly
Reverse the procedure described on the previous page.
Note:
Attach the adjust plate (5) in roughly the center of the oval hole. If this position is not correct, it will
not be possible to perform the rail slide adjustment properly. In addition, hand-tighten the selection
motor at the right end of the upper oval hole and at the left end of the lower oval hole. Because
the carrier box is an assembly, be aware that repeated re-attachment of the carrier metal (3) and
the adjust plate (5), etc., will cause the screws to lose their gripping ability.
Match up the paired holes on selection gears A (22) and B (23) and then insert them onto the
selection pin (7-A) with the positioning determined by the square hole on the selection plate
complete (7).
Readjustment
Line locator adjustment will be necessary. (Refer to 4.4.7 "Line Locator Adjustment".)
Selection motor home position adjustment will be necessary. (Refer to 4.4.2 "Selection Motor
Home Position Adjustment".)
Hammer home position adjustment will be necessary. (Refer to 4.4.3 "Hammer Position
Adjustment".)
Carrier and platen position adjustment will be necessary. (Refer to 4.4.4 "Carrier and Platen
Position Adjustment".)
Rail slide position adjustment will be necessary. (Refer to 4.4.4 "Carrier and Platen Position
Adjustment".)
Make sure that the ribbon motor gear and the selection motor gear are not loose.
Change for Ribbon and Selection motors
The production for the motors was just discontinued by Matsushita (Panasonic) Manufacturing Co.,
Ltd. so that these motors were replaced with NMB-MAT (Minebea Motor Manufacturing
Corporation).
No. Parts
(Effect
production)
Old
(Parts No.)
New (Parts No.)
14
Ribbon motor screws
(From September 2007)
M3.0 × 5
(G00-81090)
M2.6 × 5
(N00-00426)
15
Ribbon motor
(From September 2007)
Matsushita 27SIN18E9NE
(150-51110)
NMB-MAT PM25L-024-NAB8
(980-10660)
17
Selection motor screw
(From September 2007)
M3.0 × 5
(551-10040)
M2.6 × 5
(N00-00426)
18
Selection motor
(From September 2007)
Matsushita 27SIN18E9ND
(150-53310)
NMB-MAT PM25L-024-NAB7
(980-10670)
5-21
Summary of Contents for Carrera De Luxe MD
