![background image](http://html.mh-extra.com/html/olympia/carrera-de-luxe-md/carrera-de-luxe-md_service-manual_732750031.webp)
4.4.2 Selection Motor Home Position Adjustment
Check:
When the selection motor is activated, the centerline of the hammer
and the centerline of the wheel set pin must be lined up.
Adjustment:
1) Loosen the two screws (1) and then hand-tighten the selection
motor screws so that the top one is at the right end of the upper
oval (2-A) and the bottom one is at the left end of the lower oval
(2-B).
2) Enter adjustment mode.
While holding down the code key, press the express key to
activate the selection motor. (Refer to 4.3.2 "Selection Motor
Home Position and Hammer Position Adjustment Mode".)
3) Line up the two round selection gear holes (3-A and 3-B), and
then with those holes lined up with the square hole (4-A) in the
selection plate, slide the gears onto the selection plate shaft
(4-B) and engage them with the selection motor gear (4-C).
Finally, fix the selection gears (3) in place with the selection gear
stopper.
4) Mount the printwheel (6) on the selection gear (3) so that the
wheel set pin (3-C) latches onto the printwheel guide slot.
Turn the selection gear (3) so that the centerline of the wheel set
pin (3-C) is directly lined up with the center of the hammer "V"
notch (7).
5) Loosen the two screws (1), move the selection motor (2) as
indicated by the arrow and fix the printwheel in place so that the
period (".") (on the keyboard for the USA) is lined up with the
center of the "V" notch.
Press the index key and the reverse index key to check the
spokes to the left and right on the printwheel (6).
If the printwheel cannot be fixed in place in a position where it
moves the same amount to the left and the right (one character
= two steps), return to step 3 and re-assemble the assembly.
Confirmation:
After the power has been turned on and the initial operations have
been completed, make sure that the period (".") on the printwheel
(for the keyboard for the USA) comes to the center position.
Possible symptoms:
"||" or an incorrect character is printed.
This can cause the printwheel spokes to be bent or damaged.
4-5
Summary of Contents for Carrera De Luxe MD
