The function of Level 1 are:
Á. Activating or deactivating the internal buzzer.
In the case of an alarm or a
fault condition the internal buzzer will sound. To deactivate the buzzer press the ‘ON-OFF
BUZZER HELP’ key. Press the key again to activate the buzzer.
Â. Display the history record.
using the ‘F1’ key we can see the history record of
the system. In the same menu we can also see the version number of the software
installed in the device. The structure of the menu and the corresponding indications is :
6.2 Level 2 operations
are all operations that the user can do. These operations are found in a
menu. In order to access this menu the user must enter a 4 digit access code. By default this
access code is set to <0000> , but can be changed with another 4-digit code if it is required. In
order to enter level 2 (user level) we must follow the following procedure.
Press the ‘ENTER’ key . The Display shows:
If the‘0’ key is pressed 4 time then the
Display shows:
ENTER YOUR CODE
----
SELECT->ENTER
SYSTEM RESET
SELECT->ENTER
ALARM HISTORY
NOT EXIST
ALARM EVENTS
NOT EXIST
FAULT EVENTS
×× ÓÕÌÂÁÍ AL ARM
ÆÙÍÇÓ ×
×× ÂÑÁ×ÕÊÕÊËÙÌÁ
ÓÔÇ ÆÙÍÇ ×
×× ÂÑÁ×ÕÊÕÊËÙÌÁ
ÓÔÇ ÆÙÍÇ ×
×× ÂÑÁ×ÕÊÕÊËÙÌÁ
ÓÔÇ ÆÙÍÇ ×
× × Â Ñ Á × Õ Ê Õ Ê Ë Ù Ì Á
Ó Ô Ç Æ Ù Í Ç ×
×× SHORT CIRCUIT
AT ZONE ×
×× ÓÕÌÂÁÍ AL ARM
ÆÙÍÇÓ ×
×× ÓÕÌÂÁÍ AL ARM
ÆÙÍÇÓ ×
×× ÓÕÌÂÁÍ AL ARM
ÆÙÍÇÓ ×
×× ALARM EVENT
ZONE ×
SERVICE PHONE
×××××××××
SELECT->ENTER
FAULT HISTORY
SELECT->ENTER
SERVICE PHONE
CHECK
ALL DISPLAY
F1
ENTER
ESC
ESC
ESC
¹
¹
ENTER
ENTER
ENTER
If no history record
is available
If a history record
is available
Sequential blinking of
the LEDs and then
olympia
electronics
MASTER KEYBOARD
V1.08 BS114 0012
Exiting the menu
If no history record
is available
If a history record
is available
Date
File
Code
Page
09-
E
1116000.09-
E
8 from 20
GENERAL SYSTEM
RESET 15
Enter the code
”9999”
and the device will start the automatic recognition procedure and
the Display shows in sequence:
SEARCHING UNIT ××
SCI POINT -> XX
Every time that a device is found it is shown on the display(e.g. Panel Íï 1) :
UNIT FOUND
PANEL 1
When the detection procedure is finished the display shows in sequence :
GENERAL SYSTEM
RESET
HISTORY FILE HAS
DELETED
SYSTEM READY
olympia electronics
The system has deleted the history record and is ready for testing and operation .
6. Operation procedures
There are 3 operation
s
level on the panel.
Level 1.
Level 1 operation can be done directly without the need of a code.
Leve 2.
Level 2 operations are operations that are done by the user and need the user
code in order to be accessed.
Level 3.
Level 3 operation are operations and setting that are done by the installation
technician and need the technician code (service code) in order to be accessed.
All operations are done using the BS-114 control and programming keyboard. The keys
of the devices operate the same on all operation levels.
6.1 Level 1 operations
are all operations that are done by all personnel and do not require
an access code. The keys that operate in this level are :
F 1
H E L P
O N - O F F
B U Z Z E R
A L A R M
E V E N T S
FA U LT
E V E N T S
ESC
A B C D E
F G H I J
K L M N O
P Q R S T
U V W X Y
Z Ã Ä È Ë
Î Ð Ó Ö Ø
Ù # ( ) ?
% & ! + -
space
ENTER
2
1
5
4
8
7
0
3
6
9
yes
no
To enter the history
record
Used for scrolling up or down
when in menus. Displaying Alarm
or Fault events.
Internal buzzer activation
and deactivation.
Cancelling and operation or returning
to the previous menu.
Accepting and operation
or advancing to the next menu setting
Numeric
Keypad
Date
File
Code
Page
09-
E
1116000.09-
E
7 from 20
22
December
2004
22
December
2004
