RESET
ZONE 01
The setting ‘1=ACTIVE’ blinks. If the ’2’ key is pressed then the
selected zone is reset and the setting ‘2=RESET’ starts to blink.
Pressing ‘1’ again will reactivate the zone.
ZONE 01
1=ACTIVE 2=RESET
With the numeric keypad we select the required
zone and after pressing ‘ENTER’ we see :
TEST MODE
ALARM RELAY 1
The setting ‘2=DEACTIVE’ blinks. If the ‘1’ key is pressed then the relay
is activated and the setting ‘1=ACTIVE’ starts to blink. To deactivate the
relay press the ‘ 2’ key.
ALARM RELAY 1
1=ON 2=OFF
Select the ALARM relay on the required panel and
press ‘ENTER’. The Display shows:
TEST MODE
FAULT RELAY 1
The setting ‘2=DEACTIVE ’ blinks. If the ‘1’ key is pressed then the
relay is activated and the setting ‘1=ACTIVE’ starts to blink. To
deactivate the relay press the ‘2’ key.
FAULT RELAY 1
1= ON 2=OFF
Select the FAULT relay on the required panel and
press ‘ENTER’. The Display shows:
TEST MODE
SIREN 1
The setting ‘2=DEACTIVE’ blinks. If the ‘1’ key is pressed then the
output is activated and the setting‘1=ACTIVE’ starts to blink. To
deactivate the output press the ‘2’ key.
SIREN 1
1=ON 2=OFF
Select the required siren output and press
‘ENTER’. The Display shows:
TEST MODE
24V-MON ->PANEL 1
The setting
blinks . If the ‘2’ key is pressed then the
output is deactivated and the setting
.
To reactivate the output press the ‘1’ key.
‘1=ACTIVE’
‘2=DEACTIVATE’ starts to blink
24V-MON ->PANEL 1
1=ON 2=OFF
Select the output on the required panel and press
‘ENTER’ the Display shows:
The setting
blinks. If the ‘1’ key is pressed then the relay
is activated and the setting
. If a BS-117 relay module is not
‘2=DEACTIVE’
‘1=ACTIVE’ starts to blink. In order to
deactivate the relay press the ‘2’ key
REMOTE RELAY 01
1=ON 2=OFF
Select the required zone relay and press
‘ENTER’. The Display shows:
UNIT IS
NOT CONNECTED
connected to the system then this operation is
not available and the system displays the
message:
Date
File
Code
Page
09-
E
1116000.09-
E
12 from 20
7. Programming - tests - information
:
Press the ‘ENTER’ button. The Display shows:
Then
p
ress the‘1’ key four times: The Display shows:
And we have entered
in
the technician menu.
After this we can conduct a full systems check, we can modify the configuration of the
system, we can see the various voltages in different stages of the system, we can also
activate or deactivate the various options. The deletion of the history record and the
modification of the user and technician codes can also be done in this level of operation.
Level 3
operation are operation the change the default factory settings of the system.
For a
simple fire detection installation without any special requirement, there is no need for any
changes and the system can operate with the factory settings.
It is mandatory to enter this
level only if the installation requires special operations or settings.
In order to enter level 3 programming mode the technician code(service code) is required.
This is preset to <1111> but can be changed to any other 4-digit code. In order to access
level 3 operations follow the procedure described bellow
ENTER YOUR CODE
----
SELECT->ENTER
SYSTEM CHECK *
SELECT->ENTER
TEST *
TEST MODE
WALK TEST
ACTIVATE 60:00
ZONE ONE BY ONE
When the system is in this state it can be
activated by an alarm in any zone. It activates the
sirens for 2 seconds and then deactivates them
automatically.
Sequentially
the technician can test the required zones by activating a
detector or call point. To exit this mode press the‘ESC’ key. This mode
will also be exited when the time shown on the Display has
elapsed.
RESET
ZONES OF PANEL 1
setting ‘2=RESET’ starts to blink. Pressing the ‘ 1’ key reactivates all
the zones.
PANEL ZONES 1
1=ACTIVE 2=RESET
When ‘ENTER’ is pressed the Display shows:
The setting ‘1=ACTIVE’ blinks.
In this state the technician can conduct a full systems check . When
the ‘ENTER’ key is pressed the Display shows:
Date
File
Code
Page
09-
E
1116000.09-
E
11 from 20
22
December
2004
22
December
2004
7.1 Tests
The first selection of the technician menu is If we press the
‘ENTER’
TEST MODE
RELAY (1/64) 01
