The display shows:
1234567890123456
The cursor blinks over the ‘1’ digit . If we want the relay to be activated by lets say
zones 1,2,3,4,5 and 6 press the’1’ key (yes) 6 times. The cursor is moved 6
positions to the right and is positioned over the ‘7’. Press the ‘2’ key (no) 10
times and the display will show:
1234567890123456
Pressing ‘ENTER’ will activate the selection. The relay will only be activated
when one of the preselected zones (ticked) issues an alarm. We can also adjust
the operation time and the time to operate delay as described earlier.
ACTIVATE FROM
TWO ZONES (AND)
4.
The relay is activated when 2 preselected zones issue
an alarm .If this method of activation is selected the by
pressing ‘ENTER’ we must select the desired zones
on the next menu.
The Display shows:
1234567890123456
The cursor blinks over the ‘1’. If we want the relay for example to be
activated by zones 5 and 6 the press the ‘2’ key for 4 times. The curcors shifts 4
places to the right and is positioned over the ‘5’. Press the ‘1’ key (yes) 2 times
and the display shows:
1234567890123456
By pressing ‘ENTER’ the setting is activated . The relay will be activated only if
both zones 5 and 6 issue and alarm. We can also adjust the operation time and
the time to operate delay as described earlier.
The second device that can be programmed is the FAULT relay.
We select it by pressing ‘ENTER’.
CONFIGURE
FAULT RELAY 1
ACTIVATE FROM
GENERAL FAULT
After ‘ENTER’ is pressed the activation method is
shown.(default=GENERALl FAULT) If we want to
alter the activation method we must follow exactly the same procedure as
described earlier for the programming of the ALARM relay. The options and
settings are identical.
CONFIGURE
SIREN 1
ACTIVATE FROM
GENERAL ALARM
We can also program the siren output. We can
select using the ‘ FAULT EVENTS’ key
Select the required output using the numeric keypad and by pressing ‘ENTER’ we can se
e
it’s
activation method (default=general ALARM). If we want to change the activation method
press the ’FAULT EVENTS’ key and ‘ENTER’. The options available are. “ACTIVATED BY
GENERAL ALARM” and “ACTIVATED BY ZONES(OR)”. The functions of the setting are the
same as described earlier for the ALARM relay. With the option “DURATION” we can select
if the output will have a permanent or an interruptible operation. The settings are the
following:
Date
File
Code
Page
09-
E
1116000.09-
E
14 from 20
TEST MODE
HARDWARE CHECK
When ‘ENTER’ is pressed the system will start a check that includes a
HARDWARE check of the panel, the zones, the sirens, and the ‘24V-
monitored’ outputs. In every check it issues a message stating the
right or wrong configuration of each input or output.
TEST MODE
COMMUNICATIONS
External devices communication test.
7.2 Programming
The second selection in the technician menu is If we press ‘ENTER’
we enter the sytem configuration submenu.
With this submenu we can change the mode of operation of the system outputs. Before
entrance to the submenu is admitted the system warns us and ask for confirmation .
The display shows:
SELECT->ENTER
CONFIGURATION *
!!CAUTION!!
SYSTEM SETTINGS
MAYBE
CHANGED
ARE YOU SURE ?
ENTER=YES
If ‘ENTER’ is pressed we enter the system configuration submenu(programming).The
selections that are available are:
CONFIGURE
ALARM RELAY 1
ACTIVATE MODE *
GENERAL ALARM
Select the ALARM relay of the required panel and press
‘ENTER’. The
default
activation method is shown:
If we want to change the activation method then we must press the ‘FAULT
EVENTS’ key. The display shows:
Press ‘ENTER’ and using the
k
. The selections are the following:
‘FAULT EVENTS’ ey select the required
activation method
ACTIVATE FROM
GENERAL ALARM
1.
The relay is activated when any zone issues an ALARM.
By pressing the ‘ENTER’ key we can change the time that
the relay will be activated between 1 to 255 seconds
(the time 000 means continious operation) or by
ACTIVATE FROM
FAULT EVENTS
2.
The relay is activated when an error occurs. We can also
adjust the operation time and the time to operate delay
using the above mentioned method.
CHANGE MODE OF
ACTIVATION *
pressing the ‘FAULT EVENTS key we can set the delay before the relay will be
activated between 1 to 255 seconds ( the selection 000 means no delay).
ACTIVATE FROM
1-16 ZONES (OR)
3.
It is activated when one or more preselected zones
issue an alarm. If this selection is made then by
pressing ‘ENTER’ we must select the required zones
on the next menu.
Date
File
Code
Page
09-
E
1116000.09-
E
13 from 20
22
December
2004
22
December
2004
