OLT SM812-FJ-Cedar Assembly Manual Download | Manualshive

Page: 9 / 44

background image

7.

Attach

Floor Runners

to completed floor frame.

There are 2 Floor Runners per 136 1/2” side and
5 completed Runners in total. Use

6 - 2 1/2” Screws

per Runner.

Parts (Steps 7 - 9)

Floor Runners

(1 1/2” x 3 1/2” x 68 3/16”)

x 10

Hardware (Steps 7 - 9)

S1

- 2 1/2” Screws

x 60 total

8.

Make sure Runners are flush with

outside and front and rear floor framing
but not overhanging.

9.

Complete remaining Floor Runners.

10.

With Floor Runners attached, carefully flip the floor over

and place on your foundation.

Caution:

you will need 2 people to assist you. Be careful when

laying floor down not to bend or twist floor. When in place, level
floor completely.

Note:

The floor will be flipped over

and the floor runners will sit on your
foundation. It is important to note, that
having a level foundation is critical.
Choosing a foundation will vary between
regions. Typical foundations can be
concrete pads or patio stones positioned
underneath the floor runners.

Foundations

Concrete Slab
Foundation

Centered on
Floor frame.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 9

«
...
7
8
9
10
11
...
»

Summary of Contents for SM812-FJ-Cedar













































Reviews:

No comments

Related manuals for SM812-FJ-Cedar

0628RANE0504FGDD2TW1SW-V1

Brand: Mercia Garden Products Pages: 16

Brand: Dancover Pages: 67

12x8 Groundsman

Brand: Adley Pages: 6

01OVLPA0806DDFW-V2

Brand: Mercia Garden Products Pages: 6

01SHPWOR1610DDOW-V1

Brand: Mercia Garden Products Pages: 12

01DDPENT1408-V3

Brand: Mercia Garden Products Pages: 7

01DTPRMSHAX1010DDOP-V1

Brand: Mercia Garden Products Pages: 29

Brand: Solid Pages: 29

The ORGANIC GARDEN AOGC15081HC

Brand: ABSCO SHEDS Pages: 25

Brand: ABSCO SHEDS Pages: 25

Skylight 703387

Brand: Palram Pages: 53

Brand: Kerbl Pages: 2

NORDIC PLUS 15 ED-FLD

Brand: Gartenpro Pages: 45

Brand: Palmako Pages: 105

Brand: Palmako Pages: 63

the Garden Shed

Brand: Best Barns Pages: 24

Brand: Mercia Garden Products Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands