OLT SM812-FJ-Cedar Assembly Manual Download | Manualshive

Page: 43 / 44

background image

Outdoor Living Today

Flower Box Assembly Instructions

2.

Position Front Frame Piece flush with End Cap. Attach both ends with 2 - 1 1/4” screws. Pilot hole Rear

Box Frame near bottom center and secure to Base edge with 1 - 1 1/4” screw. Evenly position Front Trim
(mitre cut on end and dado cut on inside bottom) tight against front frame and nail down with 4 - 1 1/4” nails.
Position Side Trims as per Front and secure with 3 - 1 1/4” nails per side.

1.

On a table position Rear Box and End Cap Frames together so flush at top. Fasten together with

2 - 1 1/4” screws. Place Base Frame tight against Rear and End Cap and flush at bottom. Secure with
2 - 1 1/4” screws. Complete attachment of remaining End Cap Frame. Slide Front Frame between End Caps.

3.

On a flat surface, flip Flower Box on it’s rear face. Evenly space Brackets and secure through Base Frame

and into the Brackets with 2 - 1 1/4” screws per Bracket. Position completed Flower Box beneath window trim
and screw from inside of box into the center wall stud with 2 - 2” screws. (2” screws supplied with Base Kit.)

Parts Lists:

A - Base, Rear & Front Box Frames (3pcs)

3/4” x 5 1/2” x 23”

B - End Cap Frames

(2pcs)

3/4” x 5 1/2” x 7” / 8”

C - Front Trim

(1 pc)

3/4” x 1 1/2” x 26”

D - Side Trims

(2 pc)

3/4” x 1 1/2” x 8 3/4”

E - Brackets

(2 pc)

1 1/2” x 5 1/2” x 5 1/2”

F - 1 1/4” Screws

G - 1 1/4” Nails

Rear (A)

Front (A)

Base (A)

End Caps (B)

Front Trim (C)

Side Trims (D)

Brackets (E)

1 1/4”
Screws (F)

1 1/4”
Nails (G)

Rear (A)

Right Angle Cut to Rear

Flush

Base (A)

Front (A)

End Cap

Front

Flush

Front Trim

Side Trim

Rear

1 1/4” screws

Flush

2” screws

Exploded

View

1 1/4” Screw

Rear (A)

1 1/4”
Nails

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 43

«
...
41
42
43
44
»

Summary of Contents for SM812-FJ-Cedar













































Reviews:

No comments

Related manuals for SM812-FJ-Cedar

Brand: Naterial Pages: 16

Brand: Luoman Pages: 40

BYGNORDIC UNE 4,0x3,0

Brand: XL-BYG Pages: 10

Brand: Palmako Pages: 71

Brand: Palmako Pages: 92

Brand: Palmako Pages: 100

Brand: Palmako Pages: 64

Brand: Palmako Pages: 34

SpaceSaver SS124-SLIDER-METAL-FJ

Brand: OLT Pages: 39

Manhattan 1 ISO

Brand: Palmako Pages: 63

Brand: Palmako Pages: 48

Brand: Palram Pages: 83

Bella 8'x4' Series

Brand: Palram Pages: 88

Brand: Palmako Pages: 61

Brand: Palmako Pages: 38

Brand: Palmako Pages: 101

Brand: Palmako Pages: 50

Brand: Palmako Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands