OLT 12x12 Space Maker Garden Shed with Plywood Roof & AK... Assembly Manual Download Page 21

Page: 21 / 42

Parts for first Rafter Section:

2 - 3/4” x 9 1/4” x 68 1/4” - Ridge Boards
9 - 1 1/2” x 3 1/2” x 80

7/8” - Rafters

2 - 1/2” x 4 1/2” x 68 1/4” - Soffits

* Must complete 2 Rafter Sections

Remaining Rafter Pieces:

3 - 3/4” x 80” x 19 3/4” - Gussets

Important:

Locate all parts necessary to assemble each Rafter Section prior to beginning.

Steps 29- 42

to Assemble Rafter Sections. Make sure to complete on a flat, level surface.

Parts for second Rafter Section:

9 - 1 1/2” x 3 1/2” x 80

7/8” - Rafters

3 - 3/4” x 9 1/4” x 45 1/2” - Ridge Board
2 - 1/2” x 4 1/2” x 68 1/4” - Soffits

C. Rafter Section

Ridge Boards 68 1/4” (2)

Ridge Boards 45 1/2” (3)

Gussets (3)

Rafters (18)

29.

Locate

Ridge Boards

and attach together using

Metal Ridge Board Connectors

and

8 - 3/4” screws

evenly spaced on boards per

connector. Place connector approximately 1 1/4” up
from bottom of

Ridge Board

. Total length when con-

nected is 136 1/2”. Complete two

Ridge Boards

Parts (Steps 29)

Ridge Boards

(3/4” x 9 1/4” x 68 1/4”)

x 2

(3/4” x 9 1/4” x 45 1/2”)

x 3

Hardware (Steps 29)

SS2

- 3/4” Screws

x 24

total

Y9 - Metal Ridge

Connector

x3 total

Metal Ridge Board Connector

Ridge Board 68 1/4”

Ridge Board 45 1/2”

136 1/2”

8 - 3/4” screws

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 21

Ridge Boards Connectors (3)

Soffits (4)

Summary of Contents for 12x12 Space Maker Garden Shed with Plywood Roof & AK...











































Search results

Summary of Contents for 12x12 Space Maker Garden Shed with Plywood Roof & AK...

Reviews:

Related manuals for 12x12 Space Maker Garden Shed with Plywood Roof & AK...

Brands by name

Popular brands

OLT 12x12 Space Maker Garden Shed with Plywood Roof & AK..., Assembly Manual

Search results

Summary of Contents for 12x12 Space Maker Garden Shed with Plywood Roof & AK...

Reviews:

Related manuals for 12x12 Space Maker Garden Shed with Plywood Roof & AK...

Brands by name

Popular brands