background image

12x12 SunShed Garden Shed 

Plywood Roof - FJ 

Assembly Manual

Some of the safety and usage measures you may wish to consider include: 
 
-snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it is advisable to sweep the 
snow off the roof(s).  
-if the product is elevated, any structural and building code requirements are solely the customer's  
responsibility, and should be abided by.  
-in high or gusty wind conditions it is advisable to keep the structure securely grounded.  
-have a regular maintenance plan to ensure screws, doors, windows and parts are tight.  

 
 
Customer agrees to hold Outdoor Living Today free of any liability for improper installation, 
maintenance and repair of any of our products.

Revision #1.1 

April 22, 2021

Outdoor Living Today           www.outdoorlivingtoday.com             [email protected]

Page 1

Thank you for purchasing 
an 12x12 SunShed Garden 
Shed from Outdoor Living  
Today. Please take the time 
to identify all the parts prior 
to assembly.

Safety Points and Other Considerations 
Our products are built for use based on 
proper installation and normal residential 
use, on level ground. Please follow the  
instruction manual when building your  
shed and retain the manual for future  
maintenance purposes.

In the event of a missing or broken piece, simply call the Outdoor Living Today Customer 
Support Line @ 1-888-658-1658 within 30 days of the delivery of your purchase. It is our  
commitment to you to courier replacement parts, free of charge, within 10 business days of 
this notification. Replacement parts will not be provided free of charge after the 30 day grace 
period. 

Important:

 

Plywood roof panels must be covered with water proof roofing 
paper or equivalent material now. Roofing paper and roofing  
material is not supplied in this kit. 
Leaving plywood roof panels unprotected will result in water 
damage to the shed as well as delamination of the plywood.

Plywood Roof Area: 
118.6 Sq. Ft. 

Summary of Contents for 12x12 SunShed






































Reviews: