background image

59.

  Attach center panel as per Step 58. Position remaining Short Outside Roof Panel and attach 

as per 

Steps 56-57.

Toll Free 1-888-658-1658            www.outdoorlivingtoday.com           [email protected]

Page 27

Completed Polygal Side Roof Panels

61.

  Position Polygal Panel with equal gaps between 

rafters and overhanging the end of rafters by 1”.  With 
6 - 1” screws, secure panel to Polygal  Support Cleats.

equal gaps 
on each side 
of rafter.

60.

  Installation of 

6

 

Polygal Panels 

is next. 

Start by removing protective plastic layer on 
each panel. Exterior/interior side of protective 
polygal film is printed on film, be sure to note 
the side and install accordingly.  Slide panel 
up between rafters so it rests on Polygal 
Support Cleats. From the inside, carefully 
slide end of panel underneath plywood. 

63.

  Complete installation of remaining Polygal 

Panels as per 

Steps 60 - 61

.With a Caulking Gun, 

apply Silicon down each side of rafter to seal gaps 
between rafters and Polygal Panels. 

62.

  Use 3 - 3/4” screws to secure Polygal 

Panel to underside of roof plywood. 

Caulking

Summary of Contents for 12x12 SunShed






































Reviews: