background image

26. 

 Position and attach 

Side Top Plates

 on 

Side 

Riser Plates

. 35 3/4” side plates are on the outside 

with the 60” plate in the center. Angle of 

Side Plates

 

should match angle of 

F&R Top Wall Plates

. Attach 

each piece with 

4 - 1 1/4” screws

. Complete both 

sides of shed.

Parts (Steps 26)

 

Side Top Plates 

(3/4” x 2 1/2” x 60”)

 

x 2 

(3/4” x 2 1/2” x 35 3/4”)

 

x 4 

 

Hardware (Steps 26) 

S2

 

- 1 1/4” Screws

  

x 24

 

total

Top and Side 
plates flush

27. 

 Locate Triangular 

Gable Half Walls

 for 

both sides of shed. Align framing and wall siding 
lap together. Screw center wall framing of each 
piece together with 

4 - 2 1/2” screws

. Note: Prior 

to attaching, try each combination of Gables for 
best fit.Tip of Gables are separate pieces that 
need to be attached on in 

Step 28

.

Parts (Steps 27-28)

 

Gable Half Walls x 4 

 

Hardware (Steps 27-28) 

S1

 

- 2 1/2” Screws

  

x 8

 

total 

S3 - 2” Screws 

x 8 total

Male / Female Gable 
Siding Overlap

Gable End tucked inside 
Gable.

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 19

Summary of Contents for 12x12 Space Maker Garden Shed with Plywood Roof & AK...











































Reviews: