manualshive.com logo in svg

Oki POCKET PRINT 6010E, User Manual

Share
Download
Oki POCKET PRINT 6010E User Manual Download Page 96

IV - 6

Section IV - TCP/IP

OKI OkiLAN 6010e User’s Guide

Chapter 1: Introduction

Overview

This section contains instructions and information on
how to configure your OkiLAN 6010e. You will also be
instructed on how to set up your host computers to print
to the OkiLAN 6010e using the TCP/IP protocol.

OkiLAN 6010e supports three TCP/IP methods for
printing:

•

Remote Line Printer Daemon (LPD)

•

File Transfer Protocol (FTP)

•

Printing directly through a TCP port (Raw
Port Printing)

Software Requirements

The OkiLAN 6010e may be configured for TCP/IP
using the OkiNet for TCP/IP utility, or from a computer
supporting the OkiNet for NetWare utility, OR telnet
and one of the following:

•

Manual arp table entry and ping

•

Static route entry using route add command

•

DHCP

•

RARP

•

BOOTP

Summary of Contents for POCKET PRINT 6010E







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands