manualshive.com logo in svg

Oki POCKET PRINT 6010E, User Manual

Share
Download
Oki POCKET PRINT 6010E User Manual Download Page 120

IV - 30

Section IV - TCP/IP

OKI OkiLAN 6010e User’s Guide

Configuring the OkiLAN 6010e Using
OkiNet for TCP/IP

The following steps outline how to configure an
OkiLAN 6010e. To change settings of a previously
configured OkiLAN 6010e, follow the same procedure
but skip Step 3, as no prompt will appear.

1. Select the OkiLAN 6010e you wish to

configure.

2. Select Configuration from the Print Server

menu or select the Configuration icon on
the toolbar.

3. When prompted, enter the IP Address of the

OkiLAN 6010e.

4. Set the appropriate configuration by choos-

ing the applicable file folder tabs.

The following settings are configurable:

• 

TCP/IP

• 

Output Port

• 

NetWare

• 

SNMP

• 

NetWare Port

• 

Protocols

• 

NetWare Queues

• 

SNMP Traps

Summary of Contents for POCKET PRINT 6010E







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands