Oki POCKET PRINT 6010E User Manual Download Page 19

Page: 19 / 230

Har

ware Installation

I - 9

Section I - Hardware Installation

OKI OkiLAN 6010e User’s Guide

Installing the OkiLAN Utilities
Software in Windows

1. Insert the OkiLAN CD into your CD-ROM drive.
2. The Setup screen appears automatically (if it

doesn’t, click Start

→

Run, then enter D:\setup, if

“D” is your CD-ROM drive).

3. Select the utility group for the network environment

you have, then click Next.

4. Select the specific utility you want to install and the

proper location for installation, then click Install.

Windows Utility Groups:

NetWare Management Utilities

OkiNet Utility for NetWare
OkiNet Utility for NDS (Workstation and
Server)
OkiNet Utility for NDS (Workstation)

OkiNet Connect Windows Printing

OkiNet Connect for TCP/IP (Windows 95/98)
OkiNet Connect for TCP/IP (Windows NT)
OkiNet Connect for IPX/SPX (Windows 95/98)
OkiNet Connect for IPX/SPX Windows NT)
OkiNet Connect DLC (Windows 95/98)
OkiNet Connect DLC (Windows NT)

Summary of Contents for POCKET PRINT 6010E







































































































































































































































Search results

Summary of Contents for POCKET PRINT 6010E

Reviews:

Brands by name

Popular brands

Oki POCKET PRINT 6010E, User Manual

Search results

Summary of Contents for POCKET PRINT 6010E

Reviews:

Brands by name

Popular brands