Ocean Optics NeoFox Page 40 Installation And Operation Manual Download | Manualshive

Page: 40 / 68

background image

3: Using NeoFox with NeoFox Viewer Software

32

013-20000-009-02-201510

3. To save these settings through the NeoFox Sport, select

Save Settings

from the O2 Setup Menu.

Note

When the device saves a parameter through a flash write, it must save ALL of its savable settings
at the same time. Therefore, actions which may appear to save specific settings to memory will
actually save the entire set of savable parameters. Those actions include downloading calibration
data, performing a single point reset, or manually prompting a flash write by setting the Flashed
Write parameter to

Enabled

in the Advanced Settings Panel.

Resetting Saved Settings

You can reset the saved settings to their original state.

►

Procedure

1. Open the device in the NeoFox Viewer and navigate to the

Advanced Settings

screen.

2. Set the value of the Flash Reset parameter to

Enabled

. This value may revert to disabled shortly

thereafter. When the device is reset, the saved values revert to their factory settings.

3. Download your calibrations again after resetting the flash memory.

Note

For devices with firmware version 4.00 or above, the APD Bias Voltage (displayed as

DAC-APD

Gain

) setting value persists through a flash reset.

«
...
38
39
40
41
42
...
»

Summary of Contents for NeoFox





































































Reviews:

No comments

Related manuals for NeoFox

Brand: ABB Pages: 20

Brand: Utilitech Pages: 2

Brand: Jennov Pages: 50

Brand: Medeli Pages: 14

Brand: Hammond Pages: 130

Brand: Vanguard Instruments Pages: 24

Brand: J.P. Instruments Pages: 9

Brand: J.ASSY Pages: 13

Brand: jenway Pages: 50

Brand: jenway Pages: 62

Brand: Zeversolar Pages: 35

Brand: Zenner Pages: 52

Brand: Hama Pages: 16

Veeder-Root 7990 Series

Brand: Danaher Pages: 8

Brand: Rodstation Pages: 28

QI-POWER-485-300

Brand: QEED Pages: 2

Brand: Polimaster Pages: 6

Brand: STONEX Pages: 99

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands