Observator Instruments OMC-042 User Manual Download Page 49 | Manualshive

Page: 49 / 106

background image

OMC-042 / 043 / 044 Data loggers

Users

’ manual

page 49

RS485

This is solely used for Modbus communications. For info see: Generic Modbus/RTU

SDI-12

Used for SDI-12 communications, see below. For generic information on SDI-12 see:SDI-12

Measurement command

The user can choose between concurrent measurements (c), or non-concurrent (m). When the sensor
supports concurrent measurements, we strongly advise to use it. Because it saves a lot of energy. (all
sensors are measuring simultaneously). The command number is asked by the firmware, for retrieving
the right data value. For more info consult your sensors manual. After selecting the right measurement
command, the command is displayed in the menu, so the user can check this against the sensors manual

Parameters

The various data values that were retrieved from the SDI-12 sensor, can be stored into different
parameters. They behave like normal generic parameters. See more info: Parameters

SDI12 sensor

[0] Exit
[1] Name                >> SDI12
[2] Port settings       >> SDI12; 1200 Baud; Address 0
[3] Sensor power switch >> Enabled; Warm up 00:00:01
[4] Sample interval     >> Data log interval
[5] Measurement command >> 0C!
[6] Parameter 1         >> Par1
[7] Parameter 2         >> Not used
[8] Parameter 3         >> Not used
[9] Parameter 4         >> Not used
[A] Parameter 5         >> Not used
[B] Parameter 6         >> Not used
[C] Parameter 7         >> Not used
[D] Parameter 8        >> Not used
[E] Parameter 9         >> Not used
[M] More parameters     >> Not used
[R] Remove
>

«
...
47
48
49
50
51
...
»

Summary of Contents for OMC-042











































































































Reviews:

No comments

Related manuals for OMC-042

Brand: Grant Pages: 91

Brand: IRROMETER Pages: 12

Brand: EasyLog Pages: 2

Brand: Fronius Pages: 42

Electrocorder EC-1A

Brand: Acksen Pages: 3

Brand: Zebra-Tech Pages: 20

Log NFC Temperature Logger

Brand: Kaye Pages: 4

Brand: Accsys Electronics Pages: 14

Brand: METER Pages: 2

EvidenceRecorder 7

Brand: MicroSurvey Pages: 31

EasyLog 9902-2004

Brand: Lascar Electronics Pages: 2

Brand: Lascar Electronics Pages: 2

Brand: Lascar Pages: 6

Brand: Racelogic Pages: 20

Brand: Neptune Technology Pages: 52

Brand: EasyLog Pages: 2

Brand: Sigicom Pages: 51

Brand: Reflex Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands