Observator Instruments OMC-042 User Manual Download Page 9 | Manualshive

Page: 9 / 106

background image

OMC-042 / 043 / 044 Data loggers

Users

’ manual

page 9

Product Description

The data logger is designed to retrieve, and store data from various sensors. This data is logged onto the
embedded / removable SD-card. Also the stored data can be send from the data logger to any remote
computer you like. To use this feature, you need a valid SIM-card. Contact your local telecommunications
provider for more information on

the SIM card you will need. The unit accepts various power sources,

selectable  by  the  different  version  types.  The  user  should  connect  his  sensor(s)  of  preference  to  the
connector board  of the device. Captured data can  be  stored, send, visualized and manipulated in  many
ways.

The data logger is equipped with a built-in 2G/3G cellular-modem, an internal temperature sensor, 2 or 4
GB micro SD-card and a SIM card slot. The logger can be powered by an internal 3.6 Volt Lithium battery
that will last for years when the logger is configured in a low-power mode.

Depending  on  model  and  edition,  the  data  loggers  can  acquire  physical  signals  by  current  loop  inputs,
voltage inputs, resistance inputs and digital inputs. They can also be provided with an RS232/RS485/SDI-
12  port  to  capture  serial  data  (ASCII,  MODBUS/RTU,  NMEA-0183,  SDI-12)  or  to connect  an  accessory
(Camera, Display, GPS, Satellite modem).

External sensors can be powered by the data logger itself, to prevent them to consume power while the
data logger is asleep. The excitation voltage is switched off during sleep as well.

Key features:

-

A maximum sample rate of 4 Hz,

-

Recording buffer up to 4 GB,

-

Analog inputs (Except DS editions),

-

Serial port(s) (Except AD editions),

-

Digital input(s)

-

Digital output

-

Internal micro SD-card with standard FAT-32 File system for easy use with a PC,

-

Easy configuration by menu items of embedded terminal application,

-

Can be used with Windows XP, W7, W8 and W10

-

Low power / long Battery life (see specification sheet),

-

Embedded 2G/3G modem for remote operation,

-

Alarming by SMS and data delivery by HTTP, e-Mail, FTP or TCP

-

Internal voltage convertor for supplying 12 VDC power to the connected sensor(s),

-

Stable excitation voltage to power Wheatstone bridged sensors (

OMC-042 only

),

-

Firmware upgrade over the air for adding new features to your device.

-

Remote configuration over the air, for adjusting your configuration from remote.

«
...
7
8
9
10
11
...
»

Summary of Contents for OMC-042











































































































Reviews:

No comments

Related manuals for OMC-042

Brand: Wagner Meters Pages: 30

Brand: Seneca Pages: 8

Brand: Dostmann Electronic Pages: 14

Brand: Applent Instruments Pages: 76

Brand: Fluke Pages: 84

Brand: SwitchDin Pages: 8

Brand: Agilent Technologies Pages: 169

ebro EBI 20 Series

Brand: Xylem Pages: 36

Brand: Xylem Pages: 40

Brand: PASCO Pages: 4

Brand: Fluke Pages: 68

microSpider2 Industrial

Brand: Halytech Pages: 8

Brand: SolarMax Pages: 76

RSTAR Affinity Gateway

Brand: RST Instruments Pages: 24

Brand: RST Instruments Pages: 28

Brand: NexSens Technology Pages: 2

Brand: NexSens Technology Pages: 2

Brand: NexSens Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands