Observator Instruments OMC-042 User Manual Download | Manualshive

Page: 96 / 106

background image

OMC-042 / 043 / 044 Data loggers

Users

’ manual

page 96

Environment and disposal

The data logger is manufactured in compliance with the RoHS directive (Reduction of Hazardous
Substances) EU directive 2002/95/EC, which means in popular terms that the product is “lead-free”.

When the data logger is taken out of service, dispose the data logger in accordance to the local regulations
at the time the product is disposed.

Regulations for disposal of batteries may be different. Remove the batteries and dispose them in
accordance to the local regulations for batteries.

«
...
94
95
96
97
98
...
»

Summary of Contents for OMC-042











































































































Reviews:

No comments

Related manuals for OMC-042

Brand: Grant Pages: 91

Brand: Onset Pages: 4

Brand: Extech Instruments Pages: 5

Brand: Extech Instruments Pages: 7

Brand: Extech Instruments Pages: 10

AnaBat Roost Logger

Brand: TiTLEY Scientific Pages: 4

Brand: Ocean Sonics Pages: 37

Brand: Teac Pages: 69

Brand: Velleman Pages: 44

Brand: Omega Pages: 22

Brand: ICP DAS USA Pages: 221

Brand: AEM Pages: 22

SportTimer 3000

Brand: Thunderpaws Pages: 28

Brand: REED Pages: 16

Power Grid Power Module 77643

Brand: MSD Pages: 8

Brand: JRI Pages: 8

Mini SPYRF Green

Brand: JRI Pages: 10

Brand: JRI Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands