Observator Instruments OMC-042 User Manual Download Page 104

Page: 104 / 106

OMC-042 / 043 / 044 Data loggers

Users

’ manual

page 104

ERR

APN_OPEN

Error while trying to find an
internet access point

APN access point name wrong

ERR

APN_LOGIN

Error while trying to login to the
internet access point

APN user or password wrong, or
authentication failure

ERR

SERVER_LOGIN

Error while trying to login to the
Email/FTP/TCP/HTTP server

Server not available or credentials wrong

ERR

FILE_OPEN

Error while trying to open a file
on the FTP server

File handling error on the server

ERR

DATA_SENDING

Error while sending data to the
Email/FTP/TCP/HTTP server

Unexpected network disruption, or server
error

ERR

TCP_RESPONCE

Error while waiting for
acknowledge from the
TCP/HTTP server

Unexpected network disruption, or server
error

ERR

DATA_END

Error trying to disconnect from
the Email/FTP/TCP/HTTP server

Unexpected network disruption, or server
error

ERR

"STATE number"

Modem state machine step were
the error occurred

Unknown

SMS_SEND_ERR

An error occurred while sending
SMS

See the Modem ERR/WDT message
before for more details

SMS_SEND_OK

Sending of the SMS was
successful

SMS_RECV_ACVA

"Phone number"

An ACVA SMS was received

SMS_RECV_ERR

"Phone number"

An invalid SMS was received

CNT_RESET

"digital sensor name"

Shows the reset of the pulse
counter

When reset at midnight option is on, or
after manual change

STR

"Driver name;raw data"

Shows the raw data log

When this option is enabled (generic
serial string and GPS)

TIME_FIX

"+/- number of sec"

Shows the number seconds the
internal clock was adjusted

After a NTP time synchronization

TIME_FIX

"Summer time started"

Shows that the clock is adjusted
to the start of summer time

When summer time (daylight saving)
option is enabled

TIME_FIX

"Summer time ended"

Shows that the clock is adjusted
to the end of summer time

When summer time (daylight saving)
option is enabled

ALARM_SET

"Code;limit;value"

Shows the parameter code,
alarm limit and actual value

When the alarm is raised

ALARM_RESET

"Code;limit;value"

Shows the parameter code,
alarm limit and actual value

When the alarm is cleared

Summary of Contents for OMC-042











































































































Search results

Summary of Contents for OMC-042

Reviews:

Related manuals for OMC-042

Brands by name

Popular brands

Observator Instruments OMC-042, User Manual

Search results

Summary of Contents for OMC-042

Reviews:

Related manuals for OMC-042

Brands by name

Popular brands