manualshive.com logo in svg

NXP Semiconductors S32K1 Series, Hardware Design Manuallines

Share
Download
NXP Semiconductors S32K1 Series Hardware Design Manuallines Download Page 16

7.1.1 LIN components data

Table 5. LIN components

Reference

Part

Mounting

Remark

DMLIN

Diode

Mandatory only for master
ECU

Reverse Polarity protection
from LIN to VSUP.

RML1 and RML2

Resistor: 2 k

Ω

Power Loss: 250 mW

Tolerance: 1%

Package Size: 1206

Requirement:

Min Power rating of the
complete master termination
has to be ≥ 500 mW

Mandatory only for Master
ECU

For Master ECU

If more than 2 resistors are
used in parallel, the values
have to be chosen in a way
that the overall resistance RM
of 1 k

Ω

 and the minimum

power loss of the complete
master termination has to be
fulfilled.

For Slave ECU

RMLIN1 and RMLIN2 are not
needed on the PCB layout

C1

Capacitor:

Slave ECU: typically 220 pF

Master ECU: from 560 pF up
to approximately ten times that
value in the slave node
[CSLAVE], so that the total line
capacitance is less dependent
on the number of slave nodes.

Tolerance: 10%

Package Size: 0805

Voltage: ≥50 V

Mandatory

The value of the master node
has to be chosen in a way that
the LIN specification is fulfilled.

C2

Capacitor:

Package Size: 0805

Optional

Mounting of the optional part
only allowed if there is an
explicit written permission of
the respective OEM available.
Place close to the connector.

ESD1

ESD Protection

Package Size: 0603-0805

Optional

Layout pad for an additional
ESD protection part.

Mounting of the optional part
only allowed if there is an
explicit written permission of
the respective OEM available.
Place close to the connector.

NXP Semiconductors

Communication modules

Hardware Design Guidelines for S32K1xx Microcontrollers , Rev. 3, December 2018

Application Note

16 / 33

Summary of Contents for S32K1 Series


































Reviews:

No comments

Brands by name

Popular brands

Load more brands