NXP Semiconductors P5010 User Manual Download Page 62

Page: 62 / 77

P5040/P5020 Reference Design Board User Guide, Rev. 0

Freescale Semiconductor

Programming Model

NOTE

Not supported for P5040/P5020RDB.

Figure 38. Configuration Sequencer Control Register (PX_VCTL)

NOTE

PWROFF = [Default] ‘0’; normal operations do not interfere with the power
switches.
PWROFF = ‘1’ overrides any user- or APM-initiated power switch event.

7.1.18

VELA Status Register (PX_VSTAT)

The VELA status register can be used to monitor configuration sequencer activity.

NOTE

Not supported for P5040/P5020RDB.

—

WDEN

—

PWROFF

Reset

Offset

0x10

Table 45. PX_VCTL Field Descriptions

Bits

Name

Description

0–3

—

Reserved

WDEN

Watchdog Enable
• 0 - Disabled
• 1 - Enabled; must be disabled with 2^29 clock cycles (> 5 min. at 30ns clock)

or the system will reset. At any time the software can reset the bit and
disable the watchdog.

—

Reserved

PWROFF

Power Off
• [Default] 0 - Normal Power-ON
• 1 - Forced Power-OFF; HW must restore power as the software cannot

force Power-ON.

Go
• 0 - VELA sequencer is idle.
• 1 - VELA sequencer starts then halts till software resets GO to ‘0’.

Summary of Contents for P5010














































































Search results

Summary of Contents for P5010

Reviews:

NXP Semiconductors P5010, User Manual, Page: 62 / 77

Search results

Summary of Contents for P5010

Reviews: