background image

Page 9 of 14

888.901.3633 | +44 (0) 208 977 6614

www.nvtphybridge.com

Copyright © 2017 NVT Phybridge

2017/11

WIRE DISTANCE CHARTS

WIRE DISTANCE CAPACITY

The distance capability of wire is dependent on its ability to deliver DC power, and separately, to deliver high-frequency 

data signals.

The graph below shows maximum power delivery when using a 55V power supply. If you are not delivering power to 

your camera (or other remote device), then this graph does not apply. Figure 5 shows the maximum network data rate.

A Distance Calculator can be found at  www.nvtphybridge.com.

PoE devices require a minimum of 43V to operate. With a 55V supply, we have 13V of allowable voltage drop on the   

wire.

The voltage will dip in proportion to the remote (camera) load. The graph below shows what distances are supported for 

various loads and wire types.

● 

The voltage will dip in proportion to the remote (camera) load. The graph below shows what distances are  

 

supported for various loads and wire types.

● 

Start with the Powered Device (camera) wattage at the left. Sometimes PoE devices are listed as to their PoE  

 

Class rather than wattage. If this is the case, use the colored classes instead.

● 

Now read over to the right until you find your kind of wire. Then look up (feet) or down (meters) to find your  

 

maximum wire distance. If your wire is not among the examples, simply measure its total resistance and find  

 

that value on the right side of the graph. The maximum supported wattage is on the left.

Figure 5 - Data Distance Chart

Wire Distance

3.0 W

0 W

4.0 W

5.0 W

6.0 W

8.0 W

10 W

12 W

15 W

18 W

20 W

25 W

30 W

40 W

50 W

2.0 W

2.5 W

24 

38 

23 

21 

19 

16 

14 

12 

11 

28 

30 
m

40 
m

50 
m

60 
m

80 
m

100 
m

12

m

15

m

18

m

200 
m

250 
m

300 
m

400 
m

500 
m

600 
m

800 
m

1,000 

m

1,

200 
m

1,

500 
m

1,

800 
m

2,000 

m

98 ft

131 ft

164 ft 197 ft

262 ft

328 ft 397 ft

492 ft 590 ft 656 ft 820 ft 984 ft

1,312 ft

1,640 ft 1,968 ft

2,624 ft

3,280 ft 3,936 ft

4,920 ft 5,904 ft 6,560 ft

2,500 

m

3,000 

m

4,000 

m

5,000 

m

8,200 ft 9,840 ft

13,120 ft

16,400 ft

 

1

1

P E

 

C

P

C

C

PoE Class 1

 

2

P E

 

C

2

P

C

PoE Class 2

 

3

3

E

 

C

Po C

C

3

P

PoE Class 3

P E

 

C

 

4

Class

o

PoE Class 4

h

 

P

w r

H

H

i

ig

h

High

h

P

Power

Power

P we

Total Wire Resistance

Camera Wattage

NV-EC1701U Power Data Distance

6

4

4

P

r

8

/

/

//

2

22

2

2

o

P

P

P

P

r

r

C

G

1

1

PP

r

Data Limited

Cat6

  4P

r

18/2

  or  

Cat5

 4P

r

Cat6

  23

 AW

G  1

Pr

Cat5

  24

 AW

G  1

Pr

Data Limited

Complete Installation Guide

Model NV-EC1701U

EoC Ethernet over Coax Transceiver

with PoE, PoE+, or High Power PoE

Summary of Contents for NV-EC1701U















Reviews: